參數資料
型號： MIC4682
廠商： Micrel Semiconductor,Inc.
英文描述： PRECISION CURRENT LIMIT SO-8 SUPERSWITCHER BUCK REGULATOR
中文描述： 精密電流限制的SO - 8 SUPERSWITCHER降壓穩壓器
文件頁數： 10/15頁
文件大小： 226K
代理商： MIC4682
MIC4682
Applications Information
Output Voltage
The output voltage of the MIC4682 is determined by using the
following formulas:
Micrel
October 2003
10
M0334-102203
V
V
R1
R2
1
OUT
FB
=
+
R2
R1
V
V
OUT
FB
=
–
1
V
1.23V
FB
=
For most applications, a 3.01k resistor is recommended for
R1 and R2 can be calculated.
Input Capacitor
Low ESR (Equivalent Series Resistance) capacitor should be
used for the input capacitor of the MIC4862 to minimize the
input ripple voltage. Selection of the capacitor value will
depend on the input voltage range, inductor value, and the
load. Two Vishay Sprague 593D106X9050D2T(10
μ
F/50V),
tantalum capacitors are good values to use for the conditions
listed in the SOA typical tables. A 0.1
μ
F ceramic capacitor is
recommended in parallel with the tantalum capacitors to filter
the high frequency ripple. The ceramic capacitor should be
placed close to the IN pin of the MIC4682 for optimum result.
For applications that are cost sensitive, electrolytic capaci-
tors can be used but the input ripple voltage will be higher.
Diode
A Schottky diode is recommended for the output diode. Most
of the application circuits on this data sheet specify the Diode
Inc. B340A or Micro Commercial SS34A surface mount
Schottky diode. Both diodes have forward current of 3A and
low forward voltage drop. These diodes are chosen to oper-
ate at wide input voltage range and at maximum output
current. For lower output current and lower input voltage
applications, a smaller Schottky diode such as B240A or
equivalence can be used.
Inductor and Output Capacitor
A 68
μ
H inductor and a 220
μ
F tantalum output capacitor are
chosen because of their stability over the input voltage range
with maximum output current listed in the SOA typical tables.
The Sumida CDRH127-680 and Vishay Sprague
593D106X9050D2T are recommended. See
“
Bode Plots
”
for
additional information. With the same conditions, a lower
value inductor and a higher output capacitor can be used. The
disadvantages for this combination are that the output ripple
voltage will be higher and the output capacitor
’
s package size
will be bigger. For example, a 47
μ
H inductor and 330
μ
F
output capacitor are good combination. Another option is to
use a higher value inductor and a lower output capacitor. The
advantages of this combination are that the switch peak
current and the output ripple voltage will be lower. The
disadvantage is that the inductor
’
s package size will be
bigger. Applications that have lower output current require-
ment can use lower inductor value and output capacitor. See
“
Typical Application Circuits
”
for an example. A 0.1
μ
F ce-
ramic capacitor is recommended in parallel with the tantalum
output capacitor to reduce the high frequency ripple.
Current Limit Set Resistor
An external resistor connects between the ISET pin and
ground to control the current limit of the MIC4682 ranging
from 400mA to 2A. For resistor value selections, see the
“
Typical Characteristics: Current Limit vs. R
ISET
." In addition
to the R
ISET
, a resistor, ranging from 10M
to 15M
, be-
tween the ISET and IN pin is recommended for current limit
accuracy over the input voltage range.
When the MIC4682 is in current limit, the regulator is in
current mode. If the duty cycle is equal or greater than 50%,
the regulator is in the sub-harmonic region. This lowers the
average current limit. The below simplified equation deter-
mines at which input and output voltage the MIC4682 exhibits
this condition.
(
%
50
V
1
V
OUT
IN
+
)
>
.
4
Do not short or float the ISET pin. Shorting the ISET pin will
set a peak current limit greater than 2.1A. Floating the ISET
pin will exhibit unstable conditions. To disable the current limit
circuitry, the voltage at the ISET pin has to be between 2V
and 7V.
相關PDF資料
PDF描述
MIC4682BM PRECISION CURRENT LIMIT SO-8 SUPERSWITCHER BUCK REGULATOR
MIC4684 150000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN
MIC4684BM 150000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN
MIC4690 150000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN
MIC4690BM 150000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN
相關代理商/技術參數
參數描述
MIC4682_07 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Precision Current Limit SOIC-8 SuperSwitcher⑩ Buck Regulator
MIC4682BM 功能描述:IC REG BUCK 2A 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:SuperSwitcher™ 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12
MIC4682BM TR 功能描述:IC REG BUCK 2A 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:SuperSwitcher™ 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12
MIC4682YM 功能描述:直流/直流開關調節器 Precision Current Limit SO-8 Super Switcher (Lead Free) RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
MIC4682YM TR 功能描述:直流/直流開關調節器 Precision Current Limit SO-8 Super Switcher (Lead Free) RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*