- 您現在的位置：買賣IC網 > PDF目錄383611 > MIC4681BM (MICREL INC) 2A-Peak SuperSwitcher⑩ SOP-8 Buck Regulator PDF資料下載
參數資料
| 型號： | MIC4681BM |
| 廠商： | MICREL INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 2A-Peak SuperSwitcher⑩ SOP-8 Buck Regulator |
| 中文描述： | 2.1 A SWITCHING REGULATOR, 220 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | SOP-8 |
| 文件頁數： | 12/19頁 |
| 文件大?。?/td> | 395K |
| 代理商： | MIC4681BM |
MIC4681
Micrel
MIC4681
12
February 2001
θ
JA
θ
JC
θ
CA
AMBENT
printed circuit board
ground plane
heat sink area
SOP-8
Figure 2. Power SOP-8 Cross Section
Thermal Considerations
The MIC4681 SuperSwitcher
features the power-SOP-8.
This package has a standard 8-lead small-outline package
profile, but with much higher power dissipation than a stan-
dard SOP-8. Micrel's MIC4681 SuperSwitcher
family are
the first dc-to-dc converters to take full advantage of this
package.
The reason that the power SOP-8 has higher power dissipa-
tion (lower thermal resistance) is that pins 5 through 8 and the
die-attach paddle are a single piece of metal. The die is
attached to the paddle with thermally conductive adhesive.
This provides a low thermal resistance path from the junction
of the die to the ground pins. This design significantly im-
proves package power dissipation by allowing excellent heat
transfer through the ground leads to the printed circuit board.
One limitation of the maximum output current on any MIC4681
design is the junction-to-ambient thermal resistance (
θ
JA
) of
the design (package and ground plane).
Examining
θ
JA
in more detail:
θ
JA
= (
θ
JC
+
θ
CA
)
where:
θ
JC
= junction-to-case thermal resistance
θ
CA
= case-to-ambient thermal resistance
θ
JC
is a relatively constant 20
°
C/W for a power SOP-8.
θ
CA
is dependent on layout and is primarily governed by the
connection of pins 5 though 8 to the ground plane. The
purpose of the ground plane is to function as a heat sink.
θ
JA
is ideally 63
°
C/W, but will vary depending on the size of
the ground plane to which the power SOP-8 is attached.
Determining Ground-Plane Heat-Sink Area
There are two methods of determining the minimum ground
plane area required by the MIC4681.
Quick Method
Make sure that MIC4681 pins 5 though 8 are connected to a
ground plane with a minimum area of 6cm
2
. This ground
plane should be as close to the MIC4681 as possible. The
area may be distributed in any shape around the package or
on any pcb layer as long as there is good thermal contact to
pins 5 though 8 This ground plane area is more than
sufficient for most designs.
Minimum Copper/Maximum Current Method
Using Figure 3, for a given input voltage range, determine the
minimum ground-plane heat-sink area required for the
application
’
s maximum continuous output current. Figure 3
assumes a constant die temperature of 75
°
C above ambient.
0
0.5
1.0
1.5
0
5
10
AREA (cm
2
)
15
20
25
C
12V
8V
V
IN
= 30V
24V
T
A
= 50
°
C
Figure 3. Output Current vs. Ground Plane Area
When designing with the MIC4681, it is a good practice to
connect pins 5 through 8 to the largest ground plane that is
practical for the specific design.
Checking the Maximum Junction Temperature:
For this example, with an output power (P
OUT
) of 5W, (5V
output at 1A maximum with V
IN
= 12V) and 65
°
C maximum
ambient temperature, what is the maximum junction tem-
perature
Referring to the
“
Typical Characteristics: 5V Output Effi-
ciency
”
graph, read the efficiency (
η
) for 1A output current at
V
IN
= 12V or perform you own measurement.
η
= 79%
The efficiency is used to determine how much of the output
power (P
OUT
) is dissipated in the regulator circuit (P
D
).
P =P
P
OUT
η
OUT
P =5W
0.79
5W
P
D
= 1.33W
A worst-case rule of thumb is to assume that 80% of the total
output power dissipation is in the MIC4681 (P
D(IC)
) and 20%
is in the diode-inductor-capacitor circuit.
P
D(IC)
= 0.8 P
D
P
D(IC)
= 0.8
×
1.33W
P
D(IC)
= 1.064W
Calculate the worst-case junction temperature:
T
J
= P
D(IC)
θ
JC
+ (T
C
–
T
A
) + T
A(max)
where:
T
J
= MIC4681 junction temperature
P
D(IC)
= MIC4681 power dissipation
θ
JC
= junction-to-case thermal resistance.
The
θ
JC
for the MIC4681
’
s power-SOP-8 is approximately
20
°
C/W.
T
C
=
“
pin
”
temperature measurement taken at the
entry point of pins 6 or 7
相關PDF資料 |
PDF描述 |
|---|---|
| MIC4682 | PRECISION CURRENT LIMIT SO-8 SUPERSWITCHER BUCK REGULATOR |
| MIC4682BM | PRECISION CURRENT LIMIT SO-8 SUPERSWITCHER BUCK REGULATOR |
| MIC4684 | 150000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN |
| MIC4684BM | 150000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN |
| MIC4690 | 150000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC4681BM TR | 功能描述:IC REG BUCK ADJ 1A 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:SuperSwitcher™ 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12 |
| MIC4681YM | 功能描述:直流/直流開關調節器 2A Peak SuperSwitcher in SO-8 (Lead Free) RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| MIC4681YM TR | 功能描述:直流/直流開關調節器 2A Peak SuperSwitcher in SO-8 (Lead Free) RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| MIC4682 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:PRECISION CURRENT LIMIT SO-8 SUPERSWITCHER BUCK REGULATOR |
| MIC4682_07 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Precision Current Limit SOIC-8 SuperSwitcher⑩ Buck Regulator |
發布緊急采購，3分鐘左右您將得到回復。