- 您現在的位置：買賣IC網 > PDF目錄383610 > MIC3839BMM (MICREL INC) Flexible Push-Pull PWM Controller PDF資料下載
參數資料
| 型號： | MIC3839BMM |
| 廠商： | MICREL INC |
| 元件分類： | 穩壓器 |
| 英文描述： | Flexible Push-Pull PWM Controller |
| 中文描述： | 1 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封裝： | MSOP-10 |
| 文件頁數： | 10/11頁 |
| 文件大?。?/td> | 341K |
| 代理商： | MIC3839BMM |
MIC3838/3839
Micrel
MIC3838/3839
10
August 2003
RC Pin
Max ON
time
dead time
Oscillator
Reset
RAMP Pin
OUTA
OUTB
dead time
Front edge blanking
Minimum ON time
Figure 4. Timing Diagram
Error Amplifier
The error amplifier is part of the voltage control loop of the
power supply. The FB pin is the inverting input to the error
amplifier. The non-inverting input is internally connected to a
reference voltage. The output of the error amplifier, COMP,
is connected to the PWM comparator. A voltage divider
between the error amplifier output (COMP pin) and the PWM
comparator allows the error amplifier to operate in a linear
region for better transient response. The output of the error
amplifier (COMP pin) is clamped at typically 3.65V to prevent
the COMP pin from rising up too high during startup or during
a transient condition. This feature improves the transient
response of the power supply.
Output Drivers
OUTA and OUTB are alternating output stages, which switch
at half the oscillator frequency. A toggle flip-flop in the
MIC3838/9 guarantee both outputs will not be on at the same
time. The RC discharge time is the dead time, where both
outputs are off. This provides an adjustable non-overlap time
to prevent shoot through currents and transformer saturation
in the power supply.
The output drivers are inhibited when V
DD
is below the
undervoltage threshold. Internal circuitry prevents the output
drivers from glitching high when V
DD
is first applied to the
MIC3838/9 controller.
Decoupling and PCB Layout
PCB layout is critical to achieve reliable, stable and efficient
operation. A ground plane is required to control EMI and
minimize the inductance in power, signal and return paths.
The following guidelines should be followed to insure proper
operation of the circuit:
Low level signal and power grounds should be kept
separate and connected at only one location, preferably
the ground pin of the control IC. The ground signals for
the current sense, voltage feedback and oscillator
should be grouped together. The return signals for the
gate drives should be grouped together and a common
connection made at the ground pin of the controller. The
low level signals and their returns must be kept separate
from the high current and high voltage power section of
the power supply.
Avoid running sensitive traces, such as the current
sense and voltage feedback signals next to or under
power components, such as the switching FETs and
transformer.
If a current sense resistor is used, it
’
s ground end must
be located very close to the ground pin of the MIC3838/9
controller. Careful PCB layout is necessary to keep the
high current levels in the current sense resistor from
running over the low level signals in the controller.
A minimum 1
μ
F bypass capacitor must be connected
directly between the V
DD
and GND pins of the
MIC3838/9. An additional 0.1
μ
F capacitor between the
V
DD
end of the oscillator frequency setting resistor and
the ground end of the oscillator capacitor may be
necessary if the resistor is a distance away from the
main 1
μ
F bypass capacitor
相關PDF資料 |
PDF描述 |
|---|---|
| MIC39500 | 5A Low-Voltage Low-Dropout Regulator(輸出電流5A 低電壓低壓差穩壓器) |
| MIC39501 | 5A Low-Voltage Low-Dropout Regulator(輸出電流5A 低電壓低壓差穩壓器) |
| MIC4120 | 6A-Peak Low-Side MOSFET Driver |
| MIC4417 | IttyBitty Low-Side MOSFET Driver(IttyBitty技術低邊MOS場效應管驅動器) |
| MIC4417BM4 | IttyBitty⑩ Low-Side MOSFET Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC3839BMM TR | 功能描述:IC REG CTRLR ISO PWM 10-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| MIC3839YMM | 功能描述:DC/DC 開關控制器 Push-Pull DC/DC Controller (Lead Free) RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MIC3839YMM TR | 功能描述:DC/DC 開關控制器 Push-Pull DC/DC Controller (Lead Free) RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MIC384 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Three-Zone Thermal Supervisor Advance Information |
| MIC384_05 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Three-Zone Thermal Supervisor |
發布緊急采購，3分鐘左右您將得到回復。