- 您現在的位置：買賣IC網 > PDF目錄10015 > MIC3001GML (Micrel Inc)IC FOM MANAGEMENT W/CALIBR 24MLF PDF資料下載
參數資料
| 型號： | MIC3001GML |
| 廠商： | Micrel Inc |
| 文件頁數： | 29/76頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FOM MANAGEMENT W/CALIBR 24MLF |
| 標準包裝： | 75 |
| 類型： | 收發器 |
| 規程： | SDHj Sonet |
| 電源電壓： | 3 V ~ 3.6 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-VFQFN 裸露焊盤，24-MLF? |
| 供應商設備封裝： | 24-MLF?（4x4） |
| 包裝： | 管件 |
| 產品目錄頁面： | 1086 (CN2011-ZH PDF) |
| 其它名稱： | 576-1753-5 MIC3001GML-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
Micrel, Inc.
MIC3001
August 2004
35
M9999-082404-A
hbwhelp@micrel.com or (408) 955-1690
Warm Resets
The MIC3001 can be reset to its power-on default state
during operation by setting the reset bit in OEMCFG0.
When this bit is set, TXFAULT and RXLOS will be de-
asserted, all registers will be restored to their normal
power-on default values, and any A/D conversion in
progress will be halted and the results discarded. The
state
of
the
MIC3001
following
this
operation
is
indistinguishable from a power-on reset.
Power-On Hour Meter
The Power-On Hour meter logs operating hours using an
internal real-time clock and stores the result in NVRAM.
The hour count is incremented at ten-hour intervals in the
middle of each interval. The first increment therefore
takes
place
five
hours
after
power-on.
Time
is
accumulated whenever the MIC3001 is powered. The
hour meter’s timebase is accurate to 5% over all MIC3001
operating conditions. The counter is capable of storing
counts of more than thirty years, but is ultimately limited
by the write-cycle endurance of the non-volatile memory.
This implies a range of at least twenty years. Actual results
will depend on the operating conditions and write-cycle
endurance of the part in question.
Two registers, POHH and POHl, contain a 15-bit power-on
hour measurement and an error flag, POHFLT. Great care
has been taken to make the MIC3001’s hour meter immune
to data corruption and to insure that valid data is maintained
across power cycles. The hour meter employs multiple data
copies and error correction codes to maintain data validity.
This data is stored in the POHDATA registers. If POHFLT is
set, however, the power-on hour meter data has been
corrupted and should be ignored.
It is recommended that a two-byte (or more) sequential read
operation be performed on POHh and POHl to insure
coherency between the two registers. These registers are
accessible by the OEM using a valid OEM password. The
only operation that should be performed on these registers
is to clear the hour meters initial value, if necessary, at the
time of product shipment. The hour meter result may be
cleared by setting all eight POHDATA bytes to 00h.
Power-On Hour Result Format
High Byte, POHH
Low Byte, POHI
Error Flag
Elapsed Time / 10 Hours, MSBs
Elapsed Time / 10 Hours, LSBs
MSB
LSB
Table 20. Power-On Hour Meter Result Format
Test and Calibration Features
Numerous features are included in the MIC3001 to
facilitate development, testing, and diagnostics. These
features are available via registers in the OEM area. As
shown
in
Table
21,
these
features
include:
Function
Description
Control
Register(s)
Analog loop-back
Provides analog visibility of op-amp and DAC outputs via the ADC
OEMCFG0
Fault comparator disable control
Disables the fault comparator
OEMCAL0
Fault comparator spin-on-channel mode
Selects a single fault comparator channel
OEMCAL0
Fault comparator output read-back
Allows host to read individual fault comparator outputs
OEMRD
RSOUT, /INT read-back
Allows host to read the state of these pins
OEMRD
Inhibit EEPROM write cycles
Speeds repetitive writes to registers backed up by NVRAM
OEMCAL0
APC calibration mode
Allows direct writes to MODDAC and APCDAC (temperature
compensation not used)
OEMCAL0
Continuity checking
Forcing of RXLOS, TXFAULT, /INT
OEMCAL0
Halt A/D
Stops A/D conversions; ADC in one-shot mode
OEMCAL1
ADC idle flag
Indicates ADC status
OEMCAL1
A/D one-shot mode
Performs a single A/D conversion on the selected input channel
OEMCAL1
A/D spin-on-channel mode
Selects a single input channel
OEMCAL1
Channel selection
Selects ADC or fault comparator channel for spin-on-channel modes
OEMCAL1
LUT index read-back
Permits visibility of the LUT index calculated by the state-machine
LUTINDX
Manufacturer and device ID registers
Facilitates presence detection and version control
MFG_ID, DEV_ID
Table 21. Test and Diagnostic Features
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B34-MX-B1 | CONVERTER MOD DC/DC 48V 75W |
| LTC2871IFE#TRPBF | IC TXRX RS485/RS422 38-TSSOP |
| VE-24X-IU-F2 | CONVERTER MOD DC/DC 5.2V 200W |
| IDT72V3632L15PF8 | IC BIFIFO 512X36X2 15NS 120-TQFP |
| VE-B33-MX-B1 | CONVERTER MOD DC/DC 24V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC3001GML TR | 功能描述:網絡控制器與處理器 IC F/O Transceiver Mgt. IC with Internal Calibration RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MIC3001GMLTR | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:FOM Management IC with Internal Calibration |
| MIC3002 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:FOM Management IC with Internal Calibr ation |
| MIC3002_10 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:FOM Management IC with Internal Calibration |
| MIC-3002A | 制造商:ADVANTECH 制造商全稱:Advantech Co., Ltd. 功能描述:4U CompactPCI Enclosure with 6-slot 3U Backplane |
發布緊急采購，3分鐘左右您將得到回復。