- 您現在的位置：買賣IC網 > PDF目錄224284 > MIC29301-12BU (MICREL INC) High-Current Low-Dropout Regulators PDF資料下載
參數資料
| 型號： | MIC29301-12BU |
| 廠商： | MICREL INC |
| 元件分類： | 固定正電壓單路輸出LDO穩壓器 |
| 英文描述： | High-Current Low-Dropout Regulators |
| 中文描述： | 12 V FIXED POSITIVE LDO REGULATOR, 0.6 V DROPOUT, PSSO5 |
| 封裝： | TO-263, D2PAK-5 |
| 文件頁數： | 10/23頁 |
| 文件大?。?/td> | 708K |
| 代理商： | MIC29301-12BU |
Micrel, Inc.
MIC29150/29300/29500/29750
May 2010
18
M9999-050510-B
Capacitor Requirements
For stability and minimum output noise, a capacitor on
the regulator output is necessary. The value of this
capacitor is dependent upon the output current; lower
currents
allow
smaller
capacitors.
The
MIC29150/29300/29500/29750 regulators are stable
with the following minimum capacitor values at full load:
Device
Full Load Capacitor
MIC29150...............................................10F
MIC29300...............................................10F
MIC29500...............................................10F
MIC29750...............................................22F
This capacitor need not be an expensive low ESR type:
aluminum electrolytics are adequate. In fact, extremely
low ESR capacitors may contribute to instability.
Tantalum capacitors are recommended for systems
where fast load transient response is important.
Where the regulator is powered from a source with a
high AC impedance, a 0.1F capacitor connected
between Input and GND is recommended. This capacitor
should have good characteristics to above 250kHz.
Minimum Load Current
The MIC29150–29750 regulators are specified between
finite loads. If the output current is too small, leakage
currents dominate and the output voltage rises. The
following minimum load current swamps any expected
leakage current across the operating temperature range:
Device
Minimum Load
MIC29150................................................5mA
MIC29300................................................7mA
MIC29500..............................................10mA
MIC29750..............................................10mA
Adjustable Regulator Design
R1
R2
VIN
VOUT
MIC29152BT
22F
10F
Figure 4. Adjustable Regulator with Resistors
The adjustable regulator versions, MIC29xx2 and
MIC29xx3, allow programming the output voltage
anywhere between 1.25V and the 25V. Two resistors are
used. The resistor values are calculated by:
×
=
1
1.240
V
R
OUT
2
1
where VOUT is the desired output voltage. Figure 4 shows
component definition. Applications with widely varying
load currents may scale the resistors to draw the
minimum load current required for proper operation (see
“Minimum Load Current” section).
Error Flag
MIC29xx1 and MIC29xx3 versions feature an Error Flag,
which looks at the output voltage and signals an error
condition when this voltage drops 5% below its expected
value. The error flag is an open-collector output that
pulls low under fault conditions. It may sink 10mA. Low
output voltage signifies a number of possible problems,
including an overcurrent fault (the device is in current
limit) and low input voltage. The flag output is inoperative
during overtemperature shutdown conditions.
Enable Input
MIC29xx1 and MIC29xx2 versions feature an enable
(EN) input that allows ON/OFF control of the device.
Special design allows “zero” current drain when the
device is disabled—only microamperes of leakage
current flows. The EN input has TTL/CMOS compatible
thresholds for simple interfacing with logic, or may be
directly tied to ≤30V. Enabling the regulator requires
approximately 20A of current.
相關PDF資料 |
PDF描述 |
|---|---|
| MIC29203BT | 1.24 V-26 V ADJUSTABLE POSITIVE LDO REGULATOR, 0.75 V DROPOUT, PSFM5 |
| MIC29203BUT&R | 1.24 V-26 V ADJUSTABLE POSITIVE LDO REGULATOR, 0.75 V DROPOUT, PSSO5 |
| MIC29203BU | 1.24 V-26 V ADJUSTABLE POSITIVE LDO REGULATOR, 0.75 V DROPOUT, PSSO5 |
| MIC2940A-4.8BT | 4.8 V FIXED POSITIVE LDO REGULATOR, 0.6 V DROPOUT, PSFM3 |
| MIC2951-01AJB | FIXED/ADJUSTABLE POSITIVE LDO REGULATOR, 0.08 V DROPOUT, CDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC29301-12BU TR | 功能描述:IC REG LDO 12V 3A TO-263-5 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:3,000 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:3.8V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.3V @ 80mA 穩壓器數量:1 電流 - 輸出:80mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) 其它名稱:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC29301-12WT | 功能描述:低壓差穩壓器 - LDO 3.0A LDO Fixed Voltage + Flag + Shutdown (RoHS Compliant) RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MIC29301-12WU | 功能描述:低壓差穩壓器 - LDO 3.0A LDO Fixed Voltage + Flag + Shutdown RoHS Compliant RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MIC29301-12WU TR | 功能描述:低壓差穩壓器 - LDO 3.0A LDO Fixed Voltage + Flag + Shutdown RoHS Compliant RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MIC29301-3.3BT | 功能描述:IC REG LDO 3.3V 3A TO-220-5 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:3,000 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:3.8V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.3V @ 80mA 穩壓器數量:1 電流 - 輸出:80mA 電流 - 限制（最小）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) 其它名稱:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
發布緊急采購，3分鐘左右您將得到回復。