- 您現在的位置：買賣IC網 > PDF目錄383607 > MIC2810 (Micrel Semiconductor,Inc.) Digital Power Management IC 2MHz, 600mA DC/DC w/Dual 300mA/300mA Low VIN LDOs PDF資料下載
參數資料
| 型號： | MIC2810 |
| 廠商： | Micrel Semiconductor,Inc. |
| 英文描述： | Digital Power Management IC 2MHz, 600mA DC/DC w/Dual 300mA/300mA Low VIN LDOs |
| 中文描述： | 數字電源管理IC，600mA的直流/直流瓦特2MHz的/雙300mA/300mA低VIN LDO的 |
| 文件頁數： | 14/18頁 |
| 文件大?。?/td> | 520K |
| 代理商： | MIC2810 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁
Micrel, Inc.
MIC2810
SW
The switch (SW) pin connects directly to the inductor
and provides the switching current necessary to operate
in PWM mode. Due to the high speed switching on this
pin, the switch node should be routed away from
sensitive nodes.
April 2007
14
M9999-041107-B
PGND
Power ground (PGND) is the ground path for the high
current PWM mode. The current loop for the power
ground should be as small as possible.
SGND
Signal ground (SGND) is the ground path for the biasing
and control circuitry. The current loop for the signal
ground should be as small as possible.
CSET
The CSET pin is a current source output that charges a
capacitor that sets the delay time for the power-on reset
output from low to high. The delay for POR high to low
(detecting an undervoltage on any of the outputs) is
always minimal. The current source of 1.25μA charges a
capacitor up from 0V. When the capacitor reaches
1.25V, the output of the POR is allowed to go high. The
delay time in microseconds is equal to the Cset in
picofarads.
POR Delay (μs) = CSET (pF)
Component Selection
Output Capacitor
LDO1 and LDO2 outputs require a 2.2μF ceramic output
capacitor for stability. The DC/DC switch mode regulator
also requires a 2.2μF ceramic output capacitor to be
stable. All output capacitor values can be increased to
improve transient response, but performance has been
optimized for a 2.2μF ceramic on the LDOs and the
DC/DC regulator. X7R/X5R dielectric-type ceramic
capacitors
are
recommended
temperature performance. X5R/X7R-type capacitors
change capacitance by 15% over their operating
temperature range and are the most stable type of
ceramic capacitors. Z5U and Y5V dielectric capacitors
change value by as much as 50% to 60% respectively
over their operating temperature ranges.
because
of
their
Input Capacitor
A minimum 1μF ceramic, 4.7μF recommended, should
be placed as close as possible to the VIN pin for optimal
bypassing. X5R or X7R dielectrics are recommended for
the input capacitor. Y5V dielectrics lose most of their
capacitance over temperature and are therefore, not
recommended. A minimum 1μF is recommended close
to the VIN and PGND pins for high frequency filtering.
Smaller case size capacitors are recommended due to
their lower ESR and ESL. Please refer to the PCB layout
section for an example of an appropriate circuit layout.
Inductor Selection
The MIC2810 is designed for use with a 2.2μH inductor.
Proper selection should ensure the inductor can handle
the maximum average and peak currents required by the
load. Maximum current ratings of the inductor are
generally given in two methods; permissible DC current
and saturation current. Permissible DC current can be
rated either for a 40°C temperature rise or a 10% to 20%
loss in inductance. Ensure that the inductor selected can
handle the maximum operating current. When saturation
current is specified, make sure that there is enough
margin that the peak current will not saturate the
inductor. Peak inductor current can be calculated as
follows:
L
f
2
V
V
1
V
I
I
IN
OUT
OUT
OUT
PK
×
×
+
=
I
PK
:
I
OUT
:
V
IN
:
V
OUT
:
f:
L:
Peak Inductor Current
Output/Load Current
Input Voltage
Output Voltage
Switching Frequency of PWM Regulator
Inductor Value
相關PDF資料 |
PDF描述 |
|---|---|
| MIC29201 | 400mA Low-Dropout Voltage Regulator |
| MIC29201-12WT | 400mA Low-Dropout Voltage Regulator |
| MIC29201-12WU | 400mA Low-Dropout Voltage Regulator |
| MIC29201-3.3WT | 400mA Low-Dropout Voltage Regulator |
| MIC29201-3.3WU | 400mA Low-Dropout Voltage Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC2810-1JGMYML TR | 功能描述:線性穩壓器 - 標準 DC-DC + 2 Linear Regulators with LowQ mode and POR (Lead-Free) RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| MIC2810-44MYML | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: |
| MIC2810-44MYML TR | 功能描述:線性穩壓器 - 標準 DC-DC + 2 Linear Regulators with LowQ mode and POR (Lead-Free) RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| MIC2810-44MYML-TR | 功能描述:Linear And Switching Voltage Regulator IC 3 Output Step-Down (Buck) (1), Linear (LDO) (2) 2MHz 16-VFQFN, 16-MLF? 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:停產 拓?fù)?降壓（降壓）（1），線性（LDO）（2） 功能:任何功能 輸出數:3 頻率 - 開關:2MHz 電壓/電流 - 輸出 1:1.2V，600mA 電壓/電流 - 輸出 2:1.2V，300mA 電壓/電流 - 輸出 3:2.8V，300mA 帶 LED 驅動器:無 帶監控器:無 帶定序器:無 電壓 - 電源:1.65 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VFQFN，16-MLF? 供應商器件封裝:16-MLF?（4x4） 標準包裝:1 |
| MIC2810-4GKYML TR | 功能描述:線性穩壓器 - 標準 DC-DC + 2 Linear Regulators with LowQ mode and POR (Lead-Free) RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
發布緊急采購，3分鐘左右您將得到回復。