- 您現在的位置：買賣IC網 > PDF目錄384735 > MIC2660 (Micrel Semiconductor,Inc.) IttyBitty Charge Pump PDF資料下載
參數資料
| 型號： | MIC2660 |
| 廠商： | Micrel Semiconductor,Inc. |
| 英文描述： | IttyBitty Charge Pump |
| 中文描述： | IttyBitty電荷泵 |
| 文件頁數： | 4/8頁 |
| 文件大?。?/td> | 93K |
| 代理商： | MIC2660 |
MIC2660
Block Diagram
Micrel
MIC2660
4
August 1999
OSC
EN
OUT
GND
IN
MIC2660
2
×
3
×
D1
D2
D3
C1
C2
XLO
XLO
Q1
Q2
Q4
Q3
Functional Description
Refer to the block diagram.
The MIC2660 charge pump consists of an oscillator and a
voltage tripler. A logic-high applied to EN activates the
charge pump. The charge pump produces an output voltage
that is higher than the input voltage.
Supply Input
IN (supply input) is rated for +2.7V to +5.5V.
Ouput
OUT is connected to IN, less 3 diode drops, at all times.
Enable
EN (enable) is a CMOS input. A logic low turns the oscillator
off. The threshold is approximately half the supply voltage. A
floating EN input may cause unpredictable operation.
Oscillator
The oscillator produces a square wave at approximately
18MHz. It has a noninverting and an inverting output.
Crossover Lockout
The charge pump contains two crossover lockout (XLO)
circuits. Each crossover lockout circuit drives a totem pole,
consisting of a P-channel MOSFET and an N-channel MOS-
FET. The crossover lockout alternately switches the MOS-
FETs with no significant transition current (shoot-through
current from supply to ground).
Tripler
Voltage stepup is performed by charging an internal capaci-
tor then switching the charged capacitor in series with the
supply voltage to produce a higher voltage. A description of
the nominal voltage tripler output is:
V
OUT
= 3V
IN
– 3V
D
.
where:
V
OUT
= output voltage
V
IN
= supply voltage
V
D
= voltage drop across forward biased diode
All formulas are simplified. Refer to the ast paragraph of this
subsection about the actual output voltage.
The following sequence describes the basic operation of the
tripler by showing how the voltage at the “2
×
” and “3
×
” nodes,
V
2
×
and V
3
×
, increases.
Q2 turns on, completing the ground path to charge C1 (and
the 2
×
node) to the supply voltage, less a diode voltage drop.
V
2
×
(charging)
= V
IN
– V
D1
After Q2 turns off, Q1 turns on. The Q1-Q2 side of C1 is
switched (offset upward) from ground to V
IN
. The 2
×
node,
that was nominally at the supply voltage, becomes nominally
twice the supply voltage.
V
2
×
= V
IN
– V
D1
+ V
IN
While Q1 is on, Q4 is also on. When Q4 is on, the nominally
doubled voltage at the 2
×
node is applied across C2, through
D2.
V
3
×
(charging)
= V
IN
– V
D1
+ V
IN
– V
D2
After Q4 turns off, Q3 turns on. The Q3-Q4 side of C2 is
switched from ground to V
IN
. The 3
×
node, that was nomi-
nally twice the supply voltage, becomes nominally three
times the supply voltage.
V
3
×
= V
IN
– V
D1
+ V
IN
– V
D2
+ V
IN
The tripled voltage is available at the output through D3.
V
OUT
= V
IN
– V
D1
+ V
IN
– V
D2
+ V
IN
– V
D3
The output is nominally 3 times the supply voltage less the
voltage drop across three diodes.
The actual output is lower. These simplified formulas do not
show that the voltage across the capacitors decreases when
charge flows to the following stage or output. An actual
device also has some internal loss.
ESD Protection
Zener diodes are provided at IN, EN, and OUT to limit ESD
voltage.
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2660BM5 | IttyBitty Charge Pump |
| MIC2774N-XXBM5 | Dual Micro-Power Low Voltage Supervisor Advance Information |
| MIC2774H-XXBM5 | Dual Micro-Power Low Voltage Supervisor Advance Information |
| MIC2774L-XXBM5 | Dual Micro-Power Low Voltage Supervisor Advance Information |
| MIC2774 | Dual Micro-Power Low Voltage Supervisor Advance Information |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC26600YJL EV | 制造商:Micrel Inc 功能描述:Synchronous DC/DC Buck Regulator Evaluation Board for MIC26600 Series |
| MIC26600YJL TR | 功能描述:直流/直流開關調節器 26V/6A DC-DC Buck Regulator RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| MIC26600YJLTR | 制造商:Micrel 功能描述:7A Synchronous DC-DC Buck Regulator |
| MIC26600YJL-TR | 功能描述:Buck Switching Regulator IC Positive Adjustable 0.8V 1 Output 7A 28-PowerVQFN Variant, 28-MLF? 制造商:microchip technology 系列:Hyper Speed Control?，SuperSwitcher II? 包裝:剪切帶（CT） 零件狀態:Discontinued at Digi-Key 功能:降壓 輸出配置:正 拓?fù)?降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:4.5V 電壓 - 輸入（最大值）:26V 電壓 - 輸出（最小值/固定）:0.8V 電壓 - 輸出（最大值）:5.5V 電流 - 輸出:7A 頻率 - 開關:300kHz 同步整流器:是 工作溫度:-40°C ~ 125°C （TJ） 安裝類型:表面貼裝 封裝/外殼:28-PowerVQFN 變式，28-MLF? 供應商器件封裝:28-MLF?（5x6） 標準包裝:1 |
| MIC26601YJL EV | 功能描述:電源管理IC開發工具 28V/6A DC-DC Buck Regulator w/ HSC - Evaluation Board RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。