- 您現在的位置：買賣IC網 > PDF目錄384735 > MIC2592B-3BTQ (MICREL INC) Dual-Slot PCI Express Hot-Plug Controller PDF資料下載
參數資料
| 型號： | MIC2592B-3BTQ |
| 廠商： | MICREL INC |
| 元件分類： | 電源管理 |
| 英文描述： | Dual-Slot PCI Express Hot-Plug Controller |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48 |
| 封裝： | TQFP-48 |
| 文件頁數： | 18/31頁 |
| 文件大小： | 1916K |
| 代理商： | MIC2592B-3BTQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
MIC2592B
Micrel
March 2005
18
M9999-033105
V
STBY
4.99 k
/PWRGD[A/B]
AUXEN[A/B]
(1)
ON[A/B]
(1)
FORCE_ON[A/B]
(1)
(1)
External pin
(2)
CNTRL[A/B] Register Bit D[0]
(3)
Internal flag
(4)
CNTRL[A/B] Register Bit D[1]
(5)
CNTRL[A/B] Register Bit D[2]
MAIN[A/B]
(4)
VAUX[A/B]
(2)
3VAUX_UV[A/B]
(3)
FORCE_EN[A/B]
(5)
12VOUT_UV[A/B]
(3)
3VOUT_UV[A/B]
(3)
Figure 8. /PWRGD[A/B] Logic Diagram
outputs are independent of the MAIN outputs (12VIN[A/B]
and 3VIN[A/B]). Should the MAIN supply inputs move
below their respective UVLO thresholds, VAUX[A/B] will
still function as long as VSTBY[A/B] is present. Prior to
standby mode, ONA and ONB (or the Control Registers'
MAINA and MAINB bits) inputs should be deasserted or
the MIC2592B will assert /FAULT[A/B] and /INT (if inter-
rupts are enabled) output signals, if an undervoltage condi-
tion on the MAIN supply inputs is detected.
Circuit Breaker Function
The MIC2592B provides an electronic circuit breaker func-
tion that protects against excessive loads, such as short
circuits, at each supply. When the current from one or more
of a slot’s MAIN outputs exceeds the current limit threshold
(I
LIM
= 50mV/R
SENSE
) for a duration greater than t
, the
circuit breaker is tripped and both MAIN supplies (all outputs
except VAUX[A/B]) are shut off. Should the load current cause
a MAIN output’s V
SENSE
to exceed V
, the outputs are
immediately shut off with no delay. Undervoltage conditions
on the MAIN supply inputs also trip the circuit breaker, but
only when the MAIN outputs are enabled (to signal a supply
input brown-out condition).
The VAUX[A/B] outputs have a different circuit-breaker func-
tion. The VAUX[A/B] circuit breakers do not incorporate a
fast-trip detector, instead they regulate the output current into
a fault to avoid exceeding their operating current limit. The
circuit breaker will trip due to an overcurrent on VAUX[A/B]
when the fault timer expires. This use of the t
timer pre-
vents the circuit breaker from tripping prematurely due to
brief current transients.
Following a fault condition, the outputs can be turned on
again via the ON inputs (if the fault occurred on one of the
MAIN outputs), via the AUXEN inputs (if the fault occurred
on the AUX outputs), or by cycling both ON and AUXEN (if
faults occurred on both the MAIN and AUX outputs). A fault
condition can alternatively be cleared under SMI control of
the ENABLE bits in the CNTRL[A/B] registers (see Register
Bits D[1:0]). When the circuit breaker trips, /FAULT[A/B] will
FLT
THFAST
FLT
be asserted if the outputs were enabled through the Hot-Plug
Interface inputs. At the same time, /INT will be asserted (un-
less interrupts are masked). Note that /INT is deasserted by
writing a Logic 1 back into the respective fault bit position(s)
in the STAT[A/B] register or the Common Status Register.
The response time (t
FLT
) of the MIC2592B’s primary overcur-
rent detector is set by external capacitors at the CFILTER[A/B]
pins to GND. For Slot A, CFILTER[A] is located at Pin 2; for
Slot B, CFILTER[B] is located at Pin 35. For a given response
time, the value for C
FILTER[A/B]
is given by:
t
FILTER[A/B]
FILTER
C
F
ms
I
A
V
10
FLT A B
FILTER
3
where t
is the desired response time and quantities
I
FILTER
and V
cal Characteristics” table.
For applications that require a more accurate response
time for a given C
tolerance, the MIC2592B
employs a patent-pending technique that improves re-
sponse time accuracy by more than a factor of two. A
110kΩ, 1% resistor connected from the MIC2592B’s
RFILTER[A&B] pin (Pin 20) to GND can be used. In this
case, the value for C
FILTER[A/B]
for a desired response time
(t
FLT
) is given by:
t
R
FILTER[A&B]
FLT[A/B]
FILTER
are specified in the MIC2592B’s “Electri-
FILTER[A/B]
C
F
ms
k
SF
FILTER[A/B]
FLT
where t
FLT
is the desired response time, R
is 110k
, and “SF” is the CFILTER[A/B] response time
“Scaling Factor” in the “Electrical Characteristics” table.
FILTER[A&B]
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2592B-3YTQ | Dual-Slot PCI Express Hot-Plug Controller |
| MIC2592B-5BTQ | Dual-Slot PCI Express Hot-Plug Controller |
| MIC2592B-5YTQ | Dual-Slot PCI Express Hot-Plug Controller |
| MIC2596 | Dual Channel Negative Voltage Hot Swap Controllers(雙通道負電壓熱交換控制器) |
| MIC2597 | Dual Channel Negative Voltage Hot Swap Controllers(雙通道負電壓熱交換控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC2593-2BTQ | 功能描述:IC CTRLR HOTPLUG PCI DUAL 48TQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| MIC2593-2BTQ TR | 功能描述:IC PCI HOT PLUG CTLR DUAL 48TQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| MIC2593-2YTQ | 功能描述:熱插拔功率分布 Dual-slot PCI Hot Swap Power Controller w/o IPMI support - Lead Free RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MIC2593-2YTQ TR | 功能描述:熱插拔功率分布 Dual-slot PCI Hot Swap Power Controller w/o IPMI support - Lead Free RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MIC2594-1BM | 功能描述:IC CTRLR HOT SWAP NEG HV 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。