參數資料
型號: MIC2555-1BML TR
廠商: Micrel Inc
文件頁數: 11/29頁
文件大?。?/td> 0K
描述: IC TXRX UTG USB BUS UNIV 24MLF
標準包裝: 1,000
類型: 收發器
驅動器/接收器數: 1/0
規程: USB 2.0
電源電壓: 3 V ~ 4.5 V
安裝類型: 表面貼裝
封裝/外殼: 24-VFQFN 裸露焊盤,24-MLF?
供應商設備封裝: 24-MLF?(4x4)
包裝: 帶卷 (TR)
其它名稱: MIC2555-1BMLTR
Micrel, Inc.
MIC2555
December 2006
19
M9999-121406
SCL, SDA
The serial clock (SCL) and serial data (SDA) signals
implement a two-wire I
2C serial bus for control of the
MIC2555. As with all I
2C busses the MIC2555 shares a
common external pull-up resistor on each line.
INT/
The interrupt (INT/) pin is asserted while an interrupt
condition exists. It is an open drain output so that it can
be wire-ORed with other interrupt signals, and requires
an external pull-up resistor to provide a logic output. The
pull-up voltage must not be greater than VBAT.
ADR0
Because some systems may have more than one
transceiver on the I
2C bus, OTG Transceivers have been
assigned four I
2C Address locations by convention.
MIC2555 address: 01011xxb (Bit order: A6
A0)
The ADR0 pin and MIC2555’s ‘dash number’ control the
‘xx’ of MIC2555’s address, where –0 or –1 specifies the
higher order bit’s value:
Part Number
Address Range
MIC2555BML-0
0x
MIC2555BML-1
1x
Where x = the state of ADR0
D+, D-
The data plus (D+) and data minus (D-) pins output the
USB data signals. When operating as a non-USB
transceiver, the role of D+, D- change:
UART mode:
D+ = RXD
D- = TXD
GPIO_1_TX, GPIO_0_RX, GPIO_2
GPIO_0, GPIO_1, and GPIO_2 are general purpose
I/Os that can be used as data ports or interrupt sources
for the system controller, display drivers or power
switches for actuators or annunciators.
These GPIO have open drain outputs capable of sinking
at least 10 mA, can be wire ORed together, and may be
pulled above the MIC2555’s operating supply voltage,
but not beyond the 6V absolute maximum allowed. As
logic inputs, the GPIO logic thresholds are standard
CMOS thresholds set by VDD_LGC voltage.
The GPIO Input Register is a read-only register and
shows real time status of the GPIOs, independent of
other I/O settings. The GPIO Output Register holds the
desired output value for each I/O. Each I/O can act as an
independent interrupt source and can be programmed
for triggering on T
F, F
T, or both transitions
simultaneously.
The GPIO pins serve double duty as active signal pins
when called into action by the appropriate control bit:
GPIO_0 = Secondary UART Receive input.
GPIO_1 = Secondary UART Transmit output.
GPIO_2 = External charge pump oscillator input.
Audio mode:
D+
D-
Stereo
D+
Mono
D-
Mic
These are generally agreed
upon, but are not
mandatory.
相關PDF資料
PDF描述
MIC3000BML TR IC TXRX OPTICAL MANAGEMENT 24MLF
MIC3001BML TR IC FOM MANAGEMENT W/CALIBR 24MLF
MIC74BQS TR IC I/O EXPANDER I2C 8B 16QSOP
MICRF302YML TR IC ENCODER PAR QWIKRADIO 10-MLF
MK10DN512ZVLL10 IC ARM CORTEX MCU 512KB 100LQFP
相關代理商/技術參數
參數描述
MIC2555-1YML 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述:
MIC2555-1YML TR 功能描述:USB 接口集成電路 USB Transceiver - Lead Free RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
MIC2555-1YML-TR 功能描述:1/1 Transceiver Half USB 2.0 24-MLF? (4x4) 制造商:microchip technology 系列:- 包裝:剪切帶(CT) 零件狀態:有效 類型:收發器 協議:USB 2.0 驅動器/接收器數:1/1 雙工:半 接收器滯后:200mV 數據速率:400kbps 電壓 - 電源:3 V ~ 4.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤,24-MLF? 供應商器件封裝:24-MLF?(4x4) 標準包裝:1
MIC2557BM 制造商:Micrel Inc 功能描述: 制造商:Micron Technology Inc 功能描述: 制造商:Micrel Inc 功能描述:IC PCMCIA SOCKET SWITCHING MATRIX, SOIC8, IC Interface Type:-, Interface Applica
MIC2558BM 制造商:Micrel Inc 功能描述:PCMCIA Card Socket 14-Pin SOIC 制造商:Rochester Electronics LLC 功能描述:- Bulk