- 您現在的位置：買賣IC網 > PDF目錄384735 > MIC2551ABML (MICREL INC) USB TRANSCEIVER PDF資料下載
參數資料
| 型號： | MIC2551ABML |
| 廠商： | MICREL INC |
| 元件分類： | 通用總線功能 |
| 英文描述： | USB TRANSCEIVER |
| 中文描述： | LINE TRANSCEIVER, QCC16 |
| 封裝： | MLF-16 |
| 文件頁數： | 8/11頁 |
| 文件大小： | 79K |
| 代理商： | MIC2551ABML |
MIC2551A
Micrel
M9999-051004
8
May 2004
Power Supply Configuration
The MIC2551A can be set up for different power supply
configurations which modify the behavior of the device. Both
V
BUS
and V
IF
have special thresholds that detect when they
are either removed or grounded. Table 3 depicts the behavior
under the different power supply configuration scenarios that
are explained below.
Normal Mode
V
BUS
is connected to the 5.0V USB bus voltage and V
IF
is
connected to a supply voltage in the range of 1.6V to 3.6V. In
this case V
TRM
supplies a 3.3V voltage for powering the
speed select resistor via V
PU
depending on the state of CON
pin.
Disconnect Mode
V
IF
is connected to a supply in a range of 1.6V to 3.6V and
V
BUS
is open or grounded. If V
BUS
is opened while transmit-
ting, the data lines (D+, D
–
) have sharing capability and may
be driven with external devices up to approximately 3.6V if
and only if SUSPEND is enabled (SUS = 1). With V
BUS
ground, D+, D
–
sharing mode is not permitted.
Disable Mode
V
BUS
is connected to the 5.0V USB bus voltage and V
IF
is
open. All logic controlled inputs become high impedances,
thus minimal current will be supplied by V
IF
if the input pins are
pulled up to an external source.
Alternate Power Supply Configuration Options
I/O Interface Using 3.3V
In systems where the I/O interface utilizes a 3.3V USB
controller, an alternate solution is shown in Figure 7. No extra
components are required; however, the load on V
TRM
must
not exceed 10mA.
MIC2551A
VIF
VBUS
I/O
VBUS
V
/V
/
RCV/OE#
VTRM
USB
Controller
V
DD
3.3V
Figure 7. I/O Interface Using 3.3V
Bypass Input
V
BUS
and V
TRM
are tied together to a supply voltage in the
range of 3.0V to 3.6V. The internal regulator is bypassed and
the internal circuitry is run from the V
TRM
input. See Figure 8.
MIC2551A
VIF
VBUS
3.3V
VTRM
Figure 8. Powering MIC2551A
from External 3.3V
Signal Amplitude Respective to V
IF
When operating the MIC2551A, it is necessary to provide
input signals which do not exceed V
IF
+ 0.3V.
Suspend
When the suspend pin (SUS) is high, power consumption is
reduced to a minimum. V
TRM
is not disabled. RCV, V
P
and V
M
are still functional to enable the device to detect USB activity.
For minimal current consumption in suspend mode, it is
recommended that OE# = 1, and SPD = 0.
Speed
The speed pin (SPD) sets D+/D
–
output edge rates by increas-
ing or decreasing biasing current sources within the output
drivers. For low speed, SPD = 0. For full speed, SPD = 1. By
setting SPD = 0 during idle periods, in conjunction with suspend
(SUS), the lowest quiescent current can be obtained. However,
designers must provide a 300ns delay between changing SPD
from 0 to 1 and transmission of data at full speed. This delay
ensures the output drivers have arrived at their proper operating
conditions. Failure to do so can result in leading edge distortion
on the first few data bits transmitted.
External ESD Protection
The use of ESD transient protection devices is not required
for operation, but is recommended. We recommend the
following devices or the equivalent:
Cooper Electronic Technologies (www.cooperet.com)
41206ESDA SurgX
0805ESDA SurgX
Littelfuse (www.littelfuse.com)
V0402MHS05
SP0503BAHT
Non-Multiplexed Bus
In order to save pin count for the USB logic controller
interface, the MIC2551A was designed with V
P
and V
M
as bi-
directional pins. To interface the MIC2551A with a non-
multiplexed data bus, resistors can be used for low cost
isolation as shown in Figure 9.
V
PO
V
M
V
P
V
MO
USB Logic
Controller
(SIE)
MIC2551A
V
P
V
M
10k
10k
Figure 9. MIC2551A Interface to
Non-Multiplexed Data Bus
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2551ABTS | USB TRANSCEIVER |
| MIC2551 | USB TRANSCEIVER |
| MIC2570 | Two-Cell Switching Regulator(微功率升壓開關穩壓器) |
| MIC2570-1BM | Two-Cell Switching Regulator Preliminary Information |
| MIC2570-2BM | Two-Cell Switching Regulator Preliminary Information |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC2551ABML TR | 功能描述:IC USB TRANSCEIVER 16-MLF RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND |
| MIC2551ABTS | 功能描述:IC USB TRANSCEIVER 14-TSSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND |
| MIC2551ABTS TR | 功能描述:IC USB TRANSCEIVER 14-TSSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,140 系列:AU 類型:收發器 驅動器/接收器數:1/1 規程:CAN 電源電壓:5.3 V ~ 27 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SO 包裝:管件 其它名稱:935267940512AU5790D14AU5790D14-ND |
| MIC2551ABTSTR | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| MIC2551AYML | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。