- 您現在的位置：買賣IC網 > PDF目錄384734 > MIC2185 (Micrel Semiconductor,Inc.) Low Voltage Synchronous Boost PWM Control IC PDF資料下載
參數資料
| 型號： | MIC2185 |
| 廠商： | Micrel Semiconductor,Inc. |
| 英文描述： | Low Voltage Synchronous Boost PWM Control IC |
| 中文描述： | 低電壓同步升壓PWM控制IC |
| 文件頁數： | 14/15頁 |
| 文件大?。?/td> | 141K |
| 代理商： | MIC2185 |
MIC2185
Micrel
MIC2185
14
May 2002
The significant contributors to power loss at higher output
loads are (in approximate order of magnitude):
Resistive on-time losses in both MOSFETs
Switching transition losses in the low side
MOSFET
Inductor resistive losses
Current sense resistor losses
Output capacitor resistive losses (due to the
capacitor
’
s ESR)
To minimize power loss under heavy loads:
Use logic level, low on-resistance MOSFETs.
Multiplying the gate charge by the on-resistance
gives a figure of merit, providing a good balance
between switching and resistive power dissipa-
tion.
Slow transition times and oscillations on the
voltage and current waveforms dissipate more
power during the turn-on and turn-off of the low
side MOSFET. A clean layout will minimize
parasitic inductance and capacitance in the gate
drive and high current paths. This will allow the
fastest transition times and waveforms without
oscillations. Low gate charge MOSFETs will
switch faster than those with higher gate charge
specifications.
For the same size inductor, a lower value will
have fewer turns and therefore, lower winding
resistance. However, using too small of a value
will increase the inductor current and therefore
require more output capacitors to filter the output
ripple.
Lowering the current sense resistor value will
decrease the power dissipated in the resistor.
However, it will also increase the overcurrent
limit and may require larger MOSFETs and
inductor components to handle the higher
currents.
Use low ESR output capacitors to minimize the
power dissipated in the capacitor
’
s ESR.
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2185BM | Low Voltage Synchronous Boost PWM Control IC |
| MIC2185BQS | Low Voltage Synchronous Boost PWM Control IC |
| MIC2193 | 400KHZ SO 8 SYNCHRONOUS BUCK CONTROL IC |
| MIC2193BM | 400KHZ SO 8 SYNCHRONOUS BUCK CONTROL IC |
| MIC2193YM | 400KHZ SO 8 SYNCHRONOUS BUCK CONTROL IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC2185_05 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Low Voltage Synchronous Boost PWM Control IC |
| MIC2185BM | 功能描述:IC REG CTRLR BST PWM CM 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| MIC2185BM TR | 功能描述:IC REG CTRLR BST PWM CM 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| MIC2185BQS | 功能描述:IC REG CTRLR BST PWM CM 16-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| MIC2185BQS TR | 功能描述:IC REG CTRLR BST PWM CM 16-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。