- 您現在的位置：買賣IC網 > PDF目錄224284 > MIC2172BN (MICREL INC) RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS PDF資料下載
參數資料
| 型號： | MIC2172BN |
| 廠商： | MICREL INC |
| 元件分類： | 穩壓器 |
| 英文描述： | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 中文描述： | 3.5 A SWITCHING REGULATOR, 115 kHz SWITCHING FREQ-MAX, PDIP8 |
| 封裝： | PLASTIC, DIP-8 |
| 文件頁數： | 7/20頁 |
| 文件大小： | 906K |
| 代理商： | MIC2172BN |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
Micrel
MIC2172/3172
April 2006
15
M9999-041806
(408) 955-1690
()
5
2
10
1
1.68
2
0.623
4.75
L1
×
≤
IL1 ≤ 26.062H (use 27H)
Equation (3) solves for L1’s maximum current value.
L1
T
V
I
ON
IN
L1(peak) =
(3)
Where:
TON = δ / fSW = 6.23×10
-6 sec
6
L1(peak)
10
27
10
6.23
4.75
I
×
=
IL1(peak) = 1.096A
Use a 27H inductor with a peak current rating of at
least 1.4A.
Flyback Conversion
Flyback converter topology may be used in low power
applications where voltage isolation is required or
whenever the input voltage can be less than or greater
than the output voltage. As with the step-up converter
the inductor (transformer primary) current can be
continuous or discontinuous. Discontinuous operation is
recommended.
Figure 12 shows a practical flyback converter design
using the MIC3172.
Switch Operation
During Q1’s on time (Q1 is the internal NPN transistor—
see block diagrams), energy is stored in T1’s primary
inductance. During Q1’s off time, stored energy is
partially discharged into C4 (output filter capacitor).
Careful selection of a low ESR capacitor for C4 may
provide
satisfactory
output
ripple
voltage
making
additional filter stages unnecessary.
C1 (input capacitor) may be reduced or eliminated if the
MIC3172 is located near a low impedance voltage
source.
Output Diode
The output diode allows T1 to store energy in its primary
inductance (D2 nonconducting) and release energy into
C4 (D2 conducting). The low forward voltage drop of a
Schottky diode minimizes power loss in D2.
Frequency Compensation
A simple frequency compensation network consisting of
R3 and C2 prevents output oscillations.
High impedance output stages (transconductance type)
in the MIC2172/3172 often permit simplified loop-stability
solutions to be connected to circuit ground, although a
more
conventional
technique
of
connecting
the
components from the error amplifier output to its
inverting input is also possible.
Voltage Clipper
Care
must
be
taken
to
minimize
T1’s
leakage
inductance,
otherwise
it
may
be
necessary
to
incorporate the voltage clipper consisting of D1, R4, and
C3
to
avoid
second
breakdown
(failure)
of
the
MIC3172’s power NPN Q1.
Enable/Shutdown
The MIC3172 includes the enable/shutdown feature.
When the device is shutdown, total supply current is less
than 1A. This is ideal for battery applications where
portions of a system are powered only when needed. If
this feature is not required, simply connect EN to VIN or
to a TTL high voltage.
Discontinuous Mode Design
When designing a discontinuous flyback converter, first
determine whether the device can safely handle the
peak primary current demand placed on it by the output
power. Equation (8) finds the maximum duty cycle
required for a given input voltage and output power. If
the duty cycle is greater than 0.8, discontinuous
operation cannot be used.
IN(min)
CL
OUT
V
I
P
2
δ
≥
(8)
For a practical example let:
POUT = 5.0V × 0.25A = 1.25W
VIN = 4.0V to 6.0V
ICL = 1.25A when δ < 50%
Then:
4
1.25
2
δ
×
≥
δ ≥ 0.5 (50%) Use 0.55.
The slightly higher duty cycle value is used to overcome
circuit inefficiencies. A few iterations of equation (8) may
be required if the duty cycle is found to be greater than
50%.
Calculate the maximum transformer turns ratio a, or
NPRI/NSEC, that will guarantee safe operation of the
MIC2172/3172 power switch.
SEC
IN(max)
CE
V
F
V
a
±
≤
(9)
Where:
a
= transformer maximum turns ratio
VCE = power switch collector to emitter maximum
voltage
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2202YML | HIGH EFFICIENCY 2MHZ SYNCHRONOUS BUCK CONVERTER 1UP STABLE PWM REGULATOR |
| MIC2202YMM | HIGH EFFICIENCY 2MHZ SYNCHRONOUS BUCK CONVERTER 1UP STABLE PWM REGULATOR |
| MIC2558BM | PCMCIA Dual Card Socket VPP Switching Matrix |
| MIC2810-1.2/1.8/2.6YML | 1-CHANNEL POWER SUPPLY SUPPORT CKT, QCC16 |
| MIC29153BT | High-Current Low-Dropout Regulators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC2172YM | 功能描述:直流/直流開關調節器 1.25A 100kHz Switching Regulator (Lead Free) RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| MIC2172YM TR | 功能描述:直流/直流開關調節器 1.25A 100kHz Switching Regulator (Lead Free) RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| MIC2172YMTR | 制造商:Micrel 功能描述:Current Mode PWM Controller 65V 1.25A |
| MIC2172YM-TR | 制造商:Micrel Inc 功能描述: |
| MIC2172YN | 功能描述:直流/直流開關調節器 2.5A 100kHz Switching Regulator (Lead Free) RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
發布緊急采購，3分鐘左右您將得到回復。