- 您現在的位置：買賣IC網 > PDF目錄384734 > MIC2169 (Micrel Semiconductor,Inc.) 500 KHZ PWM SYNCHRONOUS BUCK CONTROL IC PDF資料下載
參數資料
| 型號： | MIC2169 |
| 廠商： | Micrel Semiconductor,Inc. |
| 英文描述： | 500 KHZ PWM SYNCHRONOUS BUCK CONTROL IC |
| 中文描述： | 500千赫的PWM同步降壓控制IC |
| 文件頁數： | 10/14頁 |
| 文件大?。?/td> | 160K |
| 代理商： | MIC2169 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁
MIC2169
Micrel
M9999-111803
10
November 2003
Voltage Setting Components
The MIC2169 requires two resistors to set the output voltage
as shown in Figure 2.
Error
Amp
7
MIC2169 [adj.]
FB
V
0.8V
R2
R1
Figure 2. Voltage-Divider Configuration
Where:
V
REF
for the MIC2169 is typically 0.8V
The output voltage is determined by the equation:
V
V
1
R1
R2
O
REF
=
×
+
A typical value of R1 can be between 3k
and 10k
. If R1 is
too large, it may allow noise to be introduced into the voltage
feedback loop. If R1 is too small, in value, it will decrease the
efficiency of the power supply, especially at light loads. Once
R1 is selected, R2 can be calculated using:
R2
V
V
R1
V
REF
O
REF
=
×
External Schottky Diode
An external freewheeling diode is used to keep the inductor
current flow continuous while both MOSFETs are turned off.
This dead time prevents current from flowing unimpeded
through both MOSFETs and is typically 15ns. The diode
conducts twice during each switching cycle. Although the
average current through this diode is small, the diode must be
able to handle the peak current.
I
I
2
80ns
f
D(avg)
OUT
S
=
×
×
×
The reverse voltage requirement of the diode is:
V
V
DIODE(rrm)
IN
=
The power dissipated by the Schottky diode is:
P
I
V
DIODE
D(avg)
F
=
×
where:
V
F
= forward voltage at the peak diode current
The external Schottky diode, D1, is not necessary for circuit
operation since the low-side MOSFET contains a parasitic
body diode. The external diode will improve efficiency and
decrease high frequency noise. If the MOSFET body diode is
used, it must be rated to handle the peak and average current.
The body diode has a relatively slow reverse recovery time
and a relatively high forward voltage drop. The power lost in
the diode is proportional to the forward voltage drop of the
diode. As the high-side MOSFET starts to turn on, the body
diode becomes a short circuit for the reverse recovery period,
dissipating additional power. The diode recovery and the
circuit inductance will cause ringing during the high-side
MOSFET turn-on. An external Schottky diode conducts at a
lower forward voltage preventing the body diode in the
MOSFET from turning on. The lower forward voltage drop
dissipates less power than the body diode. The lack of a
reverse recovery mechanism in a Schottky diode causes less
ringing and less power loss. Depending on the circuit compo-
nents and operating conditions, an external Schottky diode
will give a
1
/
2
% to 1% improvement in efficiency.
Feedback Loop Compensation
The MIC2169 controller comes with an internal
transconductance error amplifier used for compensating the
voltage feedback loop by placing a capacitor (C1) in series
with a resistor (R1) and another capacitor C2 in parallel from
the COMP pin to ground. See
“
Functional Block Diagram.
”
Power Stage
The power stage of a voltage mode controller has an inductor,
L1, with its winding resistance (DCR) connected to the output
capacitor, C
OUT
, with its electrical series resistance (ESR) as
shown in Figure 3. The transfer function G(s), for such a
system is:
ESR
C
OUT
V
O
DCR
L
Figure 3. The Output LC Filter in a Voltage Mode
Buck Converter
G(s)
1 ESR
s
+
s
C 1 ESR
C
DCR
s
C
L
s
C
2
=
× ×
×
(
)
× ×
×
× ×
Plotting this transfer function with the following assumed
values (L=2
μ
H, DCR=0.009
, C
OUT
=1000
μ
F, ESR=0.050
)
gives lot of insight as to why one needs to compensate the
loop by adding resistor and capacitors on the COMP pin.
Figures 4 and 5 show the gain curve and phase curve for the
above transfer function.
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2171BT | Isolated Flyback Switching Regulator with 9V Output |
| MIC2171BU | Isolated Flyback Switching Regulator with 9V Output |
| MIC2171 | Isolated Flyback Switching Regulator with 9V Output |
| MIC2185 | Low Voltage Synchronous Boost PWM Control IC |
| MIC2185BM | Low Voltage Synchronous Boost PWM Control IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC2169_09 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:500kHz PWM Synchronous Buck Control IC |
| MIC2169A | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:500kHz PWM Synchronous Buck Control IC |
| MIC2169A_09 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:500kHz PWM Synchronous Buck Control IC |
| MIC2169ABMM | 功能描述:IC REG CTRLR DIVIDER PWM 10-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| MIC2169ABMM TR | 功能描述:IC REG CTRLR DIVIDER PWM 10-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。