- 您現在的位置：買賣IC網 > Datasheet目錄44 > MIC2086-MBQS TR (Micrel Inc)IC CTRLR HOW SWAP SGL 20-QSOP Datasheet資料下載
參數資料
| 型號： | MIC2086-MBQS TR |
| 廠商： | Micrel Inc |
| 文件頁數： | 3/29頁 |
| 文件大?。?/td> | 1008K |
| 描述： | IC CTRLR HOW SWAP SGL 20-QSOP |
| 標準包裝： | 2,500 |
| 類型： | 熱交換控制器 |
| 應用： | 通用型 Infiniband? |
| 內部開關： | 無 |
| 電源電壓： | 2.3 V ~ 16.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 20-QSOP |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | MIC2086-MBQSTR MIC2086-MBQSTR-ND |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Micrel, Inc.
MIC2085/2086
May 2006
3
M9999-050406
(408) 955-1690
Pin Description (Cont.)
Pin Number
MIC2086
Pin Number
MIC2085
Pin Name Pin Function
4
4
ON
ON Input: Active high. The ON pin, an input to a Schmitt-triggered comparator
used to enable/disable the controller, is compared to a V
TH
reference with
100mV of hysteresis. Once a logic high is applied to the ON pin (V
ON
> 1.24V), a
start-up sequence is initiated as the GATE pin starts ramping up towards its final
operating voltage. When the ON pin receives a low logic signal (V
ON
< 1.14V),
the GATE pin is grounded and /FAULT is high if VCC is above the UVLO
threshold. ON must be low for at least 20祍 in order to initiate a start-up
sequence. Additionally, toggling the ON pin LOW to HIGH resets the circuit
breaker.
5
5
/POR
Power-On Reset Output: Open drain N-Channel device, active low. This pin
remains asserted during start-up until a time period t
POR
after the FB pin voltage
rises above the power-good threshold (VFB). The timing capacitor CPOR
determines t
POR
. When an output undervoltage condition is detected at the FB
pin, /POR is asserted for a minimum of one timing cycle, t
POR
. The /POR pin has
a weak pull-up to VCC
6
NA
PWRGD
Power-Good Output: Open drain N-Channel device, active high. When the
voltage at the FB pin is lower than 1.24V, the PWRGD output is held low. When
the voltage at the FB pin is higher than 1.24V, then PWRGD is asserted. A pull-
up resistor connected to this pin and to VCC will pull the output up to VCC. The
PWRGD pin has a weak pull-up to VCC.
7
6
/FAULT
Circuit Breaker Fault Status Output: Open drain N-Channel device, active low.
The /FAULT pin is asserted when the circuit breaker trips due to an overcurrent
condition. Also, this pin indicates undervoltage lockout and overvoltage fault
conditions. The /FAULT pin has a weak pull-up to VCC.
8
7
FB
Power-Good Threshold Input: This input is internally compared to a 1.24V
reference with 3mV of hysteresis. An external resistive divider may be used to
set the voltage at this pin. If this input momentarily goes below 1.24V, then /POR
is activated for one timing cycle, t
POR
, indicating an output undervoltage
condition. The /POR signal de-asserts one timing cycle after the FB pin exceeds
the power-good threshold by 3mV. A 5祍 filter on this pin prevents glitches from
inadvertently activating this signal.
9, 10
8
GND
Ground Connection: Tie to analog ground
11
9
OV
OV Input: When the voltage on OV exceeds its trip threshold, the GATE pin is
pulled low and the CRWBR timer starts. If OV remains above its threshold long
enough for CRWBR to reach its trip threshold, the circuit breaker is tripped.
Otherwise, the GATE pin begins to ramp up one POR timing cycle after OV
drops below its trip threshold.
12
10
COMPOUT Uncommitted Comparators Open Drain Output.
13
11
COMP+
Comparators Non-Inverting Input.
14
12
COMP-
Comparators Inverting Input.
15
Na
DIS
Discharge Output: When the MIC2086 is turned off, a 550& internal resistor at
this output allows the discharging of any load capacitance to ground.
16
13
REF
Reference Output: 1.24V nominal. Tie a 0.1礔 capacitor to ground to ensure
stability.
17
14
GATE
Gate Drive Output: Connects to the gate of an external N-Channel MOSFET. An
internal clamp ensures that no more than 13V is applied between the GATE pin
and the source of the external MOSFET. The GATE pin is immediately brought
low when either the circuit breaker trips or an undervoltage lockout condition
occurs.
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2225-4OYMT TR | IC REG DL BUCK/LINEAR 10TMLF |
| MIC2310-2ZTS TR | IC HOT SWAP CTLR 2CHAN 24TSSOP |
| MIC2341-2YTQ | IC HOT PLUG CTLR DUAL PCI 48TQFP |
| MIC2569YQS TR | IC POWER SWITCH CABLECARD 16QSOP |
| MIC2583R-MBQS TR | IC CTRLR HOT SWAP 200MV 16-QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC2086-XBQS | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Single Channel Hot Swap Controllers |
| MIC2090 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Current Limiting Power Distribution Switches |
| MIC2090_11 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Current Limiting Power Distribution Switches |
| MIC2090-1YM5 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Current Limiting Power Distribution Switches |
| MIC2090-1YM5 TR | 功能描述:電源開關 IC - USB 50mA Current Limiting Power Distribution Switch RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。