- 您現在的位置：買賣IC網 > PDF目錄383603 > MIC1832M (MICREL INC) レP Supervisory Circuit PDF資料下載
參數資料
| 型號： | MIC1832M |
| 廠商： | MICREL INC |
| 元件分類： | 電源管理 |
| 英文描述： | レP Supervisory Circuit |
| 中文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封裝： | SOIC-8 |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 164K |
| 代理商： | MIC1832M |
6
Power Monitor
The RST and RST pins are asserted whenever VCC
falls below the reset threshold voltage as determined by
the TOL pin. A 5% tolerance level (2.88V reset
threshold voltage) can be selected by connecting the
TOL pin to ground and a 10% tolerance (2.55V reset
threshold voltage) can be selected by connecting the
TOL pin to VCC. The reset pins will remain asserted for
a period of 250ms after VCChas risen above the reset
threshold voltage. The reset function ensures the
microprocessor is properly reset and powers up into a
known condition after a power failure. RST will remain
valid with VCCas low as 1.4V.
Watchdog Timer
The microprocessor can be monitored by connecting
the ST pin (watchdog input) to a bus line or I/O line. If a
high-to-low transition doesn’t occur on the ST pin within
the watchdog timeout period (determined by TD pin, see
Table 1), the RST and RST pins will be asserted
resulting in a microprocessor reset. RST and RST will
remain asserted for at least 250ms when this occurs. A
minimum pulse of 75ns or any transition high-to-low on
the ST pin will reset the watchdog timer. The watchdog
timer will be reset if ST sees a valid transition within the
watchdog timeout period.
Pushbutton Reset Input
The PBRST input can be driven with a manual
pushbutton switch or with external logic signals. The
input is internally debounced and requires an active low
signal to force the reset outputs into their active states.
The PBRST input will recognize any pulse that is 20ms
in duration or greater and will ignore all pulses that are
less than 1ms in duration.
Figure 1. Power-Up/Power-Down Sequence
Circuit Description
V
CC
RST
RST
t
RPU
V
CCTP
t
RPD
V
CCTP
Figure 3. Pushbutton Reset
Figure 2. Watchdog Input
RST
RST
t
RST
t
PDLY
PBRST
t
PB
t
TD
ST
t
ST
Note:
The maximum time between high-to-low transitions (t
TD
) on the
watchdog input (ST) is determined by the voltage applied to the
TD pin. If the watchdog input sees a high-to-low transition prior to
the timeout period, the watchdog timer will be reset.
MIC1832
μ
P Supervisory Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| MIC1832N | RSO-S_D(Z) Series - Econoline Regulated DC-DC Converters; Input Voltage (Vdc): 05V; Output Voltage (Vdc): 3.3V; Power: 1W; 2:1 and 4:1 Wide Input Voltage Ranges; 1kVDC, 2kVD & 3kVDC Isolation; UL94V-0 Package Material; Continuous Short Circuit Protectionwith Current Foldback; Low Noise; No External Capacitor needed; Efficiency to 83% |
| MIC184 | Local/Remote Thermal Supervisor Advance Information |
| MIC184BM | Local/Remote Thermal Supervisor Advance Information |
| MIC184BMM | Local/Remote Thermal Supervisor Advance Information |
| MIC204 | SINGLE CHANNEL HIGH CURRENT LOW VOLTAGE, PROTECTED POWER DISTRIBUTION SWITCH |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC1832M TR | 功能描述:IC SUPERVISOR 2.88/2.55V 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:標準傳輸延遲為 60 µs 電壓 - 閥值:3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:Digi-Reel® 其它名稱:LM8364BALMF30DKR |
| MIC1832MY | 功能描述:監控電路 Microprocessor Supervisor with Manual Reset, Watchdog Timer, 2.55V or 2.88V Threshold Voltage, 250ms Reset Pulse, and Push-Pull Active-High and Low Outputs (DS1832) RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MIC1832MY TR | 功能描述:監控電路 Microprocessor Supervisor with Manual Reset, Watchdog Timer, 2.55V or 2.88V Threshold Voltage, 250ms Reset Pulse, and Push-Pull Active-High and Low Outputs (DS1832) RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MIC1832N | 功能描述:IC SUPERVISOR 2.88/2.55V 8-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:標準傳輸延遲為 60 µs 電壓 - 閥值:3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:Digi-Reel® 其它名稱:LM8364BALMF30DKR |
| MIC1832NY | 功能描述:監控電路 Microprocessor Supervisor with Manual Reset, Watchdog Timer, 2.55V or 2.88V Threshold Voltage, 250ms Reset Pulse, and Push-Pull Active-High and Low Outputs (DS1832) RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。