- 您現在的位置：買賣IC網 > PDF目錄371098 > MF0060M-03ATxx (Mitsubishi Electric Corporation) null8/16-bit Data Bus Flash ATA PC Card PDF資料下載
參數資料
| 型號： | MF0060M-03ATxx |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | null8/16-bit Data Bus Flash ATA PC Card |
| 中文描述： | null8/16-bit數據總線閃存阿拉木圖PC卡 |
| 文件頁數： | 18/29頁 |
| 文件大?。?/td> | 841K |
| 代理商： | MF0060M-03ATXX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
MITSUBISHI STORAGE CARD
ATA PC CARDS
MITSUBISHI
ELECTRIC
18
1997.Nov. Rev. 1.2
Check Power Mode(98h, E5h)
This command checks the power mode.
Execute Drive Diagnostic(90h)
This command performs the internal diagnostic tests
implemented by the card.
Erase Sector(s)(C0h)
This command is used to pre-erase and condition data
sectors in advance of a Write without Erase or Write
Multiple without Erase command.
Format Track(50h)
This command writes the desired head and cylinder of the
selected drive with a FFh pattern.
Identify Drive(ECh)
This command enables the host to receive parameter
information from the card. (Refer to the Identify Drive
Information table.)
Idle(97h, E3h)
This command causes the card to set BSY, enter the Idle
mode, clear BSY and generate an interrupt. If the sector
count is non-zero, the automatic power down mode is
enabled. If the sector count is zero, the automatic power
down mode is disabled.
Idle Immediate(95h, E1h)
This command causes the card to set BSY, enter the idle
mode, clear BSY and generate an interrupt.
Initialize Drive Parameters(91h)
This command allows the host to alter the number of
sectors per track and the number of heads per cylinder.
Read Buffer(E4h)
This command enables the host to read the current
contents of the card’s sector buffer.
Read Long Sector(22h, 23h)
This command is similar to the Read Sector(s) command
except the contents of the Sector Count register are
ignored and only one sector is read. The 512 data bytes
and 4 ECC bytes are read into the buffer(with no ECC
correction) and then transferred to the host.
Read Multiple(C4h)
This command performs similarly to the Read Sector(s)
command. Interrupt are not generated on each sector, but
on the transfer of a block which contains the number of
sectors defined by a Set Multiple command.
Read Sector(s)(20h, 21h)
This command transfers data from the card to the host.
Data transfer starts at the sector specified by the Cylinder,
Head, and Sector Number registers, and proceeds for the
number of sectors specified in the Sector Count register.
Read Verify Sector(s)(40h, 41h)
This command is identical to the Read Sector(s)
command, except that DRQ is not asserted, and no data is
transferred to the host.
Recalibrate(1xh)
Although this command is supported for backward
compatibility, it has no actual function. The card will
always return good status at the completion of this
command.
Request Sense(03h)
This command requests extended error information for the
previous command.
Seek(7xh)
This command is supported for backward compatibility.
Although this command has no actual function, it does
perform a range check of valid track, and posts an IDNF
error if the Head or Cylinder specified are out of bounds.
Set Features(EFh)
This command is used by the host to establish or select
certain features.
Set Multiple Mode(C6h)
This command enables the card to perform Read and
Write Multiple operations and establishes the block count
for these commands. This card supports 1 sector block
size.
Set Sleep Mode(E6h, 99h)
This command causes the card to set BSY, enter the Sleep
mode, clear BSY and generate an interrupt.
Standby(96h, E2h)
This command causes the card to set BSY, enter the
Standby mode, clear BSY and generate an interrupt.
Standby Immediate(94h, E0h)
This command causes the card to set BSY, enter the
Standby mode, clear BSY and generate an interrupt.
Wear Leveling(F5h)
Although this command is supported for backward
compatibility, it has no actual function. The card will
always return good status at the completion of this
command.
Write Buffer(E8h)
This command enables the host to overwrite contents of
the card’s sector buffer with any data pattern desired. This
command has the same protocol as the Write Sector(s)
command and transfers 512 bytes.
Write Long Sector(32h, 33h)
This command is similar to the Write Sector(s) except the
contents of the Sector Count register are ignored and only
相關PDF資料 |
PDF描述 |
|---|---|
| MF0075M-03ATxx | null8/16-bit Data Bus Flash ATA PC Card |
| MF0090M-03ATxx | ER 26C 26#16 SKT RECP |
| MF0105M-03ATxx | null8/16-bit Data Bus Flash ATA PC Card |
| MF007M5-03ATXX | ER 8C 8#12 PIN RECP |
| MF0015M-03ATxx | null8/16-bit Data Bus Flash ATA PC Card |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MF0064M-04AAXX | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:8/16-bit Data Bus CompactFlash Card |
| MF0064M-04BAXX | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:8/16-bit Data Bus CompactFlash Card |
| MF0064M-05AAXX | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:8/16-bit Data Bus CompactFlash Card |
| MF0064M-07ATXX | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:8/16-bit Data Bus Flash ATA PC Card |
| MF0064M-07BTXX | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:8/16-bit Data Bus Flash ATA PC Card |
發布緊急采購，3分鐘左右您將得到回復。