參數資料
型號： MF0032M-05AAXX
廠商： Mitsubishi Electric Corporation
英文描述： GT 5C 5#16S SKT PLUG
中文描述： 16位產品數據總線CF卡
文件頁數： 18/32頁
文件大?。?/td> 589K
代理商： MF0032M-05AAXX
MITSUBISHI STORAGE CARD
Preliminary
MF0XXXX-05AAXX series
CompactFlash CARDS
MITSUBISHI
ELECTRIC
18 June.2001
. Rev. 1.3
Check Power Mode(98h, E5h)
This command checks the power mode.
Execute Drive Diagnostic(90h)
This command performs the internal diagnostic tests
implemented by the card.
Erase Sector(s)(C0h)
This command is used to pre-erase and condition data
sectors in advance of a Write without Erase or Write
Multiple without Erase command.
Format Track(50h)
This command writes the desired head and cylinder of
the selected drive with a FFh pattern.
Identify Drive(ECh)
This command enables the host to receive parameter
information from the card. (Refer to the Identify Drive
Information table.)
Idle(97h, E3h)
This command causes the card to set BSY, enter the Idle
mode, clear BSY and generate an interrupt. If the sector
count is non-zero, the automatic power down mode is
enabled. If the sector count is zero, the automatic power
down mode is disabled.
Idle Immediate(95h, E1h)
This command causes the card to set BSY, enter the idle
mode, clear BSY and generate an interrupt.
Initialize Drive Parameters(91h)
This command allows the host to alter the number of
sectors per track and the number of heads per cylinder.
Read Buffer(E4h)
This command enables the host to read the current
contents of the card’s sector buffer.
Read Long Sector(22h, 23h)
This command is similar to the Read Sector(s)
command except the contents of the Sector Count
register are ignored and only one sector is read. The 512
data bytes and 4 ECC bytes are read into the buffer(with
no ECC correction) and then transferred to the host.
Read Multiple(C4h)
This command performs similarly to the Read Sector(s)
command. Interrupt are not generated on each sector,
but on the transfer of a block which contains the number
of sectors defined by a Set Multiple command.
Read Sector(s)(20h, 21h)
This command transfers data from the card to the host.
Data transfer starts at the sector specified by the
Cylinder, Head, and Sector Number registers, and
proceeds for the number of sectors specified in the
Sector Count register.
Read Verify Sector(s)(40h, 41h)
This command is identical to the Read Sector(s)
command, except that DRQ is not asserted, and no data
is transferred to the host.
Recalibrate(1xh)
Although this command is supported for backward
compatibility, it has no actual function. The card will
always return good status at the completion of this
command.
Request Sense(03h)
This command requests extended error information for
the previous command.
Seek(7xh)
This command is supported for backward compatibility.
Although this command has no actual function, it does
perform a range check of valid track, and posts an IDNF
error if the Head or Cylinder specified are out of
bounds.
Set Features(EFh)
This command is used by the host to establish or select
certain features.
Set Multiple Mode(C6h)
This command enables the card to perform Read and
Write Multiple operations and establishes the block
count for these commands. This card supports 1 sector
block size.
Set Sleep Mode(99h, E6h)
This command causes the card to set BSY, enter the
Sleep mode, clear BSY and generate an interrupt.
相關PDF資料
PDF描述
MF0256M-07BTxx 8/16-bit Data Bus Flash ATA PC Card
MF0064M-07BTXX 8/16-bit Data Bus Flash ATA PC Card
MF0064M-07ATXX 8/16-bit Data Bus Flash ATA PC Card
MF0256M-07ATxx 8/16-bit Data Bus Flash ATA PC Card
MF1037S-1 FOR PERSONAL HANDYPHONE SYSTEM
相關代理商/技術參數
參數描述
MF0032M-11ATXX 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:8/16-bit Data Bus Flash ATA PC Card
MF0040 功能描述:安裝硬件 MOUNTING FEET FOR RP SERIES RoHS:否 制造商:Harwin 類型:SMT Cable Clip 材料:Phosphor Bronze 安裝孔大小: 長度:5 mm 外徑: 內徑: 厚度: 電鍍:Tin 螺紋大小:
MF0041 制造商:SPC Multicomp 功能描述:WALL FIXING KIT RP RANGE
MF0041 制造商:SPC Multicomp 功能描述:WALL FIXING KIT RP RANGE
MF0045 功能描述:安裝硬件 RoHS:否 制造商:Harwin 類型:SMT Cable Clip 材料:Phosphor Bronze 安裝孔大小: 長度:5 mm 外徑: 內徑: 厚度: 電鍍:Tin 螺紋大小:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*