- 您現在的位置：買賣IC網 > PDF目錄45378 > MD80C32-30SCD (ATMEL CORP) 8-BIT, 30 MHz, MICROCONTROLLER, CDIP40 PDF資料下載
參數資料
| 型號： | MD80C32-30SCD |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, 30 MHz, MICROCONTROLLER, CDIP40 |
| 封裝： | 0.600 INCH, CERAMIC, DIP-40 |
| 文件頁數： | 105/182頁 |
| 文件大小： | 2994K |
| 代理商： | MD80C32-30SCD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁當前第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁
29
1477K–AVR–08/10
ATtiny26(L)
Calibrated Internal
RC Oscillator
The calibrated internal RC Oscillator provides a fixed 1.0, 2.0, 4.0, or 8.0 MHz clock. All frequen-
cies are nominal values at 5V and 25
°C. This clock may be selected as the system clock by pro-
gramming the CKSEL Fuses as shown in Table 11. If selected, it will operate with no external
components. The CKOPT Fuse should always be unprogrammed when using this clock option.
During Reset, hardware loads the calibration byte into the OSCCAL Register and thereby auto-
matically calibrates the RC Oscillator. At 5V, 25
°C and 1.0 MHz Oscillator frequency selected,
this calibration gives a fre-quency within ± 3% of the nominal frequency. Using run-time calibra-
tion methods as described in application notes available at www.atmel.com/avr it is possible to
achieve ± 1% accuracy at any given VCC and Temperature. When this oscillator is used as the
chip clock, the Watchdog Oscillator will still be used for the Watchdog Timer and for the reset
time-out. For more information on the pre-programmed calibration value, see the section “Cali-
Note:
1. The device is shipped with this option selected.
When this oscillator is selected, start-up times are determined by the SUT Fuses as shown in
Table 12. PB4 (XTAL1) and PB5 (XTAL2) can be used as general I/O ports.
Note:
1. The device is shipped with this option selected.
Oscillator Calibration
Register – OSCCAL
Bits 7..0 – CAL7..0: Oscillator Calibration Value
Writing the calibration byte to this address will trim the internal oscillator to remove process vari-
ations from the oscillator frequency. During Reset, the 1 MHz calibration value which is located
in the signature row high byte (address 0x00) is automatically loaded into the OSCCAL Register.
If the internal RC is used at other frequencies, the calibration value must be loaded manually.
This can be done by first reading the signature row by a programmer, and then store the calibra-
tion values in the Flash or EEPROM. Then the value can be read by software and loaded into
the OSCCAl Register. When OSCCAL is zero, the lowest available frequency is chosen. Writing
non-zero values to this register will increase the frequency of the internal oscillator. Writing $FF
to the register gives the highest available frequency. The calibrated Oscillator is used to time
Table 11. Internal Calibrated RC Oscillator Operating Modes
CKSEL3..0
Nominal Frequency (MHz)
0001(1)
1.0
0010
2.0
0011
4.0
0100
8.0
Table 12. Start-up Times for the Internal Calibrated RC Oscillator Clock Selection
SUT1..0
Start-up Time from
Power-down
Additional Delay from
Reset (VCC = 5.0V)
Recommended Usage
00
6 CK
–
BOD enabled
01
6 CK
4.1 ms
Fast rising power
10(1)
6 CK
65 ms
Slowly rising power
11
Reserved
Bit
76543210
CAL7
CAL6
CAL5
CAL4
CAL3
CAL2
CAL1
CAL0
OSCCAL
Read/Write
R/W
Initial Value
Device Specific Calibration Value
相關PDF資料 |
PDF描述 |
|---|---|
| MR83C154TXXX-20P883R | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CQCC44 |
| MQ80C52XXX-25SBR | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQFP44 |
| MC80C32-20SHXXX | 8-BIT, 20 MHz, MICROCONTROLLER, CDIP40 |
| MD80C52EXXX-20SHXXX | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CDIP40 |
| MR80C32E-16/883:R | 8-BIT, 16 MHz, MICROCONTROLLER, CQCC44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MD80C51 | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 44 MHz Single-Chip 8 Bit Microcontroller |
| MD80C51BH | 制造商:ROCHESTER 制造商全稱:ROCHESTER 功能描述:CMOS SINGLE - CHIP 8-BIT MICROCOMPUTER 64K program Memory Space |
| MD80C51FB | 制造商:Rochester Electronics LLC 功能描述: |
| MD80C86 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 16-Bit Microprocessor |
| MD80C862 | 制造商:Intel 功能描述:PROCESSOR:MICRO-PROCESSOR |
發布緊急采購，3分鐘左右您將得到回復。