參數資料
型號： MCZ33993EWR2
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： Multiple Switch Detection Interface
中文描述： 多交換檢測接口
文件頁數： 10/28頁
文件大?。?/td> 504K
代理商： MCZ33993EWR2
Analog Integrated Circuit Device Data
Freescale Semiconductor
10
33993
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
WAKE-UP (WAKE)
The WAKE pin is an open-drain output and a wake-up
input. The pin is designed to control a power supply Enable
pin. In the Normal mode, the WAKE pin is low. In the Sleep
mode, the WAKE pin is high. The WAKE pin has a pull-up to
the internal +5.0 V supply.
In Sleep mode with the WAKE pin high, falling edge of
WAKE will place the 33993 in Normal mode. In Sleep mode
with V
DD
applied, the INT pin must be high for negative edge
of WAKE to wake up the device. If V
DD
is not applied to the
device in Sleep mode, INT does not affect the WAKE
operation.
BATTERY INPUT (VPWR)
The V
PWR
pin is battery input and Power-ON Reset to the
33993 IC. The V
PWR
pin requires external reverse battery
and transient protection. Maximum input voltage on V
PWR
is
50 V. All wetting, sustain, and internal logic current is
provided from the V
PWR
pin.
VOLTAGE DRAIN SUPPLY (VDD)
The VDD input pin is used to determine logic levels on the
microprocessor interface (SPI) pins. Current from VDD is
used to drive SO output and the pull-up current for CS and
INT pins. V
DD
must be applied for wake-up from negative
edge of CS or INT.
GROUND (GND)
The GND pin provides ground for the IC as well as ground
for inputs programmed as switch-to-battery inputs.
PROGRAMMABLE SWITCHES 0–7 (SP0 – SP7)
The 33993 device has 8 switch inputs capable of being
programmed to read switch-to-ground or switch-to-battery
contacts. The input is compared with a 4.0 V reference.
When programmed to be switch-to-battery, voltages greater
than 4.0 V are considered closed. Voltages less than 4.0 V
are considered open. The opposite holds true when inputs
are programmed as switch-to-ground. Programming features
are defined in
Table 5
through
Table 10
in the
Logic
Commands and Registers
section of this datasheet. Voltages
greater than the V
PWR
supply voltage will source current
through the SP inputs to the V
PWR
pin. Transient battery
voltages greater than 40 V must be clamped by an external
device.
SWITCH-TO-GROUND INPUTS 0–13 (SG0 – SG13)
The SGn pins are switch-to-ground inputs only. The input
is compared with a 4.0 V reference. Voltages greater than
4.0 V are considered open. Voltages less than 4.0 V are
considered closed. Programming features are defined in
Table 5
through
Table 10
in the
Logic Commands and
Registers
section of this datasheet. Voltages greater than the
V
PWR
supply voltage will source current through the SG
inputs to the V
PWR
pin. Transient battery voltages greater
than 40 V must be clamped by an external device.
相關PDF資料
PDF描述
MCZ146010EGR2 Low Power CMOS Photoelectric Smoke Detector IC
MCZ146012EGR2 Low Power CMOS Photoelectric Smoke Detector IC
MCF5211CAE66 ColdFire Microcontroller
MCF5211CEP66 ColdFire Microcontroller
MCF5211LCEP66 ColdFire Microcontroller
相關代理商/技術參數
參數描述
MCZ33996CEK 制造商:Freescale Semiconductor 功能描述:16 LOW SIDE SW - Bulk
MCZ33996CEKR2 制造商:Freescale Semiconductor 功能描述:16 LOW SIDE SW - Tape and Reel
MCZ33996EK 功能描述:開關變換器、穩壓器與控制器 16 LOW SIDE SW RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
MCZ33996EK 制造商:Freescale Semiconductor 功能描述:IC LOAD SWITCH 27V 32SOIC
MCZ33996EKR2 功能描述:開關變換器、穩壓器與控制器 16 LOW SIDE SW 1.20HM RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*