- 您現在的位置：買賣IC網 > PDF目錄359155 > MCZ33887EK (飛思卡爾半導體(中國)有限公司) 5.0 A H-Bridge with Load Current Feedback PDF資料下載
參數資料
| 型號： | MCZ33887EK |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | 5.0 A H-Bridge with Load Current Feedback |
| 中文描述： | 5.0的H -橋的負載電流反饋 |
| 文件頁數： | 21/37頁 |
| 文件大?。?/td> | 524K |
| 代理商： | MCZ33887EK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
21
33887
FUNCTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
Numerous protection and operational features (speed,
torque, direction, dynamic braking, PWM control, and closed-
loop control), in addition to the 5.0 A current capability, make
the 33887 a very attractive, cost-effective solution for
controlling a broad range of small DC motors. In addition, a
pair of 33887 devices can be used to control bipolar stepper
motors. The 33887 can also be used to excite transformer
primary windings with a switched square wave to produce
secondary winding AC currents.
FUNCTIONAL PIN DESCRIPTIONS
POWER GROUND AND ANALOG GROUND
(PGND AND AGND)
Power and analog ground pins should be connected
together with a very low impedance connection.
POSITIVE POWER SUPPLY (V+)
V+ pins are the power supply inputs to the device. All V+
pins must be connected together on the printed circuit board
with as short as possible traces offering as low impedance as
possible between pins.
V+ pins have an undervoltage threshold. If the supply
voltage drops below a V+ undervoltage threshold, the output
power stage switches to a tri-state condition and the fault
status flag is SET and the Fault Status pin voltage switched
to a logic LOW. When the supply voltage returns to a level
that is above the threshold, the power stage automatically
resumes normal operation according to the established
condition of the input pins and the fault status flag is
automatically reset logic HIGH.
As V+ increases in value above 28 V, the charge pump
performance begins to degrade. At +40 V, the charge pump
is effectively non-functional. Operation at this high voltage
level will result in the output FETs not being enhanced when
turned on. This means that the voltage on the output will be
V
OUT
= (V+) – V
GS
. This increased voltage drop under load
will produce a higher power dissipation.
FAULT STATUS (FS)
The
FS
pin is the device fault status output. This output is
an active LOW open drain structure requiring a pull-up
resistor to 5.0 V. Refer to
Table 6, Truth Table
,
page
20
.
LOGIC INPUT CONTROL AND DISABLE
(IN1, IN2, D1, AND D2)
These pins are input control pins used to control the
outputs. These pins are 5.0 V CMOS-compatible inputs with
hysteresis. The IN1 and IN2 independently control OUT1 and
OUT2, respectively. D1 and
D2
are complementary inputs
used to tri-state disable the H-Bridge outputs.
When either D1 or
D2
is SET (D1 = logic HIGH or
D2
=
logic LOW) in the disable state, outputs OUT1 and OUT2 are
both tri-state disabled; however, the rest of the circuitry is fully
operational and the supply I
Q (standby)
current is reduced to a
few milliamperes. Refer to
Table 6, Truth Table
,
and
STATIC
ELECTRICAL CHARACTERISTICS
table, page
9
.
H-BRIDGE OUTPUT (OUT1 AND OUT2)
These pins are the outputs of the H-Bridge with integrated
output MOSFET body diodes. The bridge output is controlled
using the IN1, IN2, D1, and
D2
inputs. The low-side
MOSFETs have active current limiting above the I
LIM
threshold. The outputs also have thermal shutdown (tri-state
latch-OFF) with hysteresis as well as short circuit latch-OFF
protection.
A disable timer (time t
b
) USED to detect currents that are
higher than current limit is activated at each output activation
to facilitate hard short detection (see
Figure 11
, page
13
).
Charge Pump Capacitor (CCP)
A filter capacitor (up to 33 nF) can be connected from the
charge pump output pin and PGND. The device can operate
without the external capacitor, although the C
CP
capacitor
helps to reduce noise and allows the device to perform at
maximum speed, timing, and PWM frequency.
ENABLE (EN)
The EN pin is used to place the device in a sleep mode so
as to consume very low currents. When the EN pin voltage is
a logic LOW state, the device is in the sleep mode. The
device is enabled and fully operational when the EN pin
voltage is logic HIGH. An internal pull-down resistor
maintains the device in sleep mode in the event EN is driven
through a high impedance I/O or an unpowered
microcontroller, or the EN input becomes disconnected.
FEEDBACK FOR H-BRIDGE (FB)
The 33887 has a feedback output (FB) for “real time”
monitoring of H-Bridge high-side current to facilitate closed-
loop operation for motor speed and torque control.
The FB pin provides current sensing feedback of the
H-Bridge high-side drivers. When running in forward or
reverse direction, a ground referenced 1/375th (0.00266) of
load current is output to this pin. Through an external resistor
to ground, the proportional feedback current can be
converted to a proportional voltage equivalent and the
controlling microcontroller can “read” the current proportional
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33889BEG | System Basis Chip with Low Speed Fault Tolerant CAN Interface |
| MCZ33927EK | Transistor; Type: Amplifiers/Bipolar; VCEO (V): -100; Ic (A): -1; Pc (W): 0.9; hFE: 140 to 350; VCE (sat) (V) max: -0.5; Package: TO-92Mod |
| MCZ33970EG | Dual Gauge Driver Integrated Circuit with Improved Damping Algorithms |
| MCZ33976EG | Dual Gauge Driver with Configurable esponse Time |
| MCZ33977EG | Single Gauge Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33887EKR2 | 功能描述:馬達/運動/點火控制器和驅動器 H-BRIDGE W/LD CUR FDBK RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33887EKR2DH | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:5.0 A H-Bridge with Load Current Feedback |
| MCZ33889BEG | 功能描述:網絡控制器與處理器 IC SBC-LITE-LS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCZ33889BEG | 制造商:Freescale Semiconductor 功能描述:IC SYSTEM BASIS W/CAN TRANCEIVER |
| MCZ33889BEG/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:System Basis Chip with Low Speed Fault Tolerant CAN Interface |
發布緊急采購，3分鐘左右您將得到回復。