參數資料
型號: MCZ33399EF
廠商: 飛思卡爾半導體(中國)有限公司
英文描述: Local Interconnect Network (LIN) Physical Interface
中文描述: 本地互連網絡(LIN)物理接口
文件頁數: 12/19頁
文件大?。?/td> 234K
代理商: MCZ33399EF
Analog Integrated Circuit Device Data
Freescale Semiconductor
12
33399
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
As described below and depicted in
Figure 10
and
Table 5
on page
13
, the 33399 has two operational modes, normal
and sleep, and one transitional mode, Awake.
NORMAL MODE
This is the normal transmitting and receiving mode. All
features are available.
SLEEP MODE
In this mode the transmission path is disabled and the
device is in low power mode. Supply current from V
SUP
is
20 μA typical. Wake-up can occur from LIN bus activity, as
well as from node internal wake-up through the EN pin and
the WAKE input pin.
DEVICE POWER-UP (AWAKE TRANSITIONAL
MODE)
At system power-up (V
SUP
rises from zero), the 33399
automatically switches into the “Awake
mode (refer to
Figure 10
below and
Table 5
on page
13
. It switches the INH
pin in HIGH state to V
SUP
level. The microcontroller of the
application then confirms the Normal mode by setting the EN
pin HIGH.
DEVICE WAKE-UP EVENTS
The device can be awakened from Sleep mode by three
wake-up events:
LIN bus activity
Internal node wake-up (EN pin)
Wake-up from WAKE pin
Figures
7
,
8
, and
9
on page
9
show device application
circuit and detail of wake-up operations.
Wake-Up from LIN Bus (Awake Transitional Mode)
A wake-up from the LIN pin switching from recessive to
dominant state (switch from V
SUP
to GND) can occur. This is
achieved by a node sending a wake-up frame on the bus.
This condition internally wakes up the interface, which
switches the INH pin to a HIGH level to enable the voltage
regulator. The device switches into the Awake
mode. The
microcontroller and the complete application power up. The
microcontroller must switch the EN pin to a HIGH level to
allow the device to leave the Awake
mode and turn it into
Normal
mode in order to allow communication on the bus.
Wake-Up from Internal Node Activity (Normal Mode)
The application can internally wake up. In this case the
microcontroller of the application sets the EN pin in the HIGH
state. The device switches into Normal
mode.
Wake-Up from WAKE Pin (Awake Transitional Mode)
The application can wake up with the activation of an
external switch. Refer to
Table 1, 8-SOICN Pin Definitions
on
page 3
.
Figure 10. Operational and Transitional Modes State Diagram
Power-Up/
Down
Sleep
Awake
Normal
1.0 to 20
kbps
EN LOW
LIN Bus or WAKE Pin
Wake-Up
EN HIGH
EN HIGH (Local Wake-Up Event)
V
PWR
> 7.0 V
Note
Refer to Table 5 for explanation.
V
PWR
< 7.0 V
V
PWR
< 7.0 V
V
PWR
< 7.0 V
相關PDF資料
PDF描述
MCZ33661EF Local Area Network (LIN) Enhanced Physical Interface with Selectable Slew Rate
MCZ33689DEW System Basis Chip with LIN Transceiver
MCZ33742EG System Basis Chip (SBC) with Enhanced High-Speed CAN Transceiver
MCZ33790EG Two-Channel Distributed System Interface (DSI) Physical Interface Device
MCZ33793AEF Distributed System Interface (DSI) Sensor Interface
相關代理商/技術參數
參數描述
MCZ33399EFR2 功能描述:輸入/輸出控制器接口集成電路 LIN INTERFACE RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
MCZ33661EF 功能描述:網絡控制器與處理器 IC ENHANCED LIN INTERFACE RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCZ33661EF 制造商:Freescale Semiconductor 功能描述:IC INTERFACE PHYSICAL LINE 8SOIC
MCZ33661EFR2 功能描述:網絡控制器與處理器 IC ENHANCED LIN INTERFACE RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCZ33661EFR2 制造商:Freescale Semiconductor 功能描述:IC LIN INTERFACE 制造商:Freescale Semiconductor 功能描述:IC, LIN INTERFACE