I2C BUS CHARACTERISTICS
鍙冩暩(sh霉)璩囨枡
鍨嬭櫉(h脿o)锛� MCP79400T-I/ST
寤犲晢锛� Microchip Technology
鏂囦欢闋�(y猫)鏁�(sh霉)锛� 14/15闋�(y猫)
鏂囦欢澶�?銆�?/td> 0K
鎻忚堪锛� IC RTCC 64B SRAM GP I2C 8TSSOP
妯�(bi膩o)婧�(zh菙n)鍖呰锛� 2,500
椤炲瀷锛� 鏅�(sh铆)閻�/鏃ユ
鐗归粸(di菐n)锛� 璀﹀牨(b脿o)鍣�锛岄枏骞�锛屾柟娉㈣几鍑猴紝SRAM锛屽敮涓€ ID
瀛樺劜(ch菙)瀹归噺锛� 64B
鏅�(sh铆)闁撴牸寮忥細 HH:MM:SS锛�12/24 灏忔檪(sh铆)锛�
鏁�(sh霉)鎿�(j霉)鏍煎紡锛� YY-MM-DD-dd
鎺ュ彛锛� I²C锛�2 绶氫覆鍙�
闆绘簮闆诲锛� 1.8 V ~ 5.5 V
闆诲 - 闆绘簮锛岄浕姹狅細 1.3 V ~ 5.5 V
宸ヤ綔婧害锛� -40°C ~ 85°C
瀹夎椤炲瀷锛� 琛ㄩ潰璨艰
灏佽/澶栨锛� 8-TSSOP锛�0.173"锛�4.40mm 瀵級
渚涙噳(y墨ng)鍟嗚ō(sh猫)鍌欏皝瑁濓細 8-TSSOP
鍖呰锛� 甯跺嵎 (TR)
MCP7940X
DS25009C-page 8
2011 Microchip Technology Inc.
4.0
I2C BUS CHARACTERISTICS
4.1
I2C Interface
The MCP7940X supports a bidirectional 2-wire bus and
data transmission protocol. A device that sends data
onto the bus is defined as transmitter, and a device
receiving data as receiver. The bus has to be controlled
by a master device which generates the Start and Stop
conditions, while the MCP7940X works as slave. Both
master and slave can operate as transmitter or receiver
but the master device determines which mode is
activated.
4.1.1
BUS CHARACTERISTICS
The following bus protocol has been defined:
Data transfer may be initiated only when the bus
is not busy.
During data transfer, the data line must remain
stable whenever the clock line is high. Changes in
the data line while the clock line is high will be
interpreted as a Start or Stop condition.
Accordingly, the following bus conditions have been
defined (Figure 4-1).
4.1.1.1
Bus not Busy (A)
Both data and clock lines remain high.
4.1.1.2
Start Data Transfer (B)
A high-to-low transition of the SDA line while the clock
(SCL) is high determines a Start condition. All
commands must be preceded by a Start condition.
4.1.1.3
Stop Data Transfer (C)
A low-to-high transition of the SDA line while the clock
(SCL) is high determines a Stop condition. All
operations must end with a Stop condition.
4.1.1.4
Data Valid (D)
The state of the data line represents valid data when,
after a Start condition, the data line is stable for the
duration of the high period of the clock signal.
The data on the line must be changed during the low
period of the clock signal. There is one bit of data per
clock pulse.
Each data transfer is initiated with a Start condition and
terminated with a Stop condition. The number of the
data bytes transferred between the Start and Stop
conditions is determined by the master device.
4.1.1.5
Acknowledge
Each receiving device, when addressed, is obliged to
generate an Acknowledge signal after the reception of
each byte. The master device must generate an extra
clock pulse which is associated with this Acknowledge
bit.
A device that acknowledges must pull down the SDA
line during the Acknowledge clock pulse in such a way
that the SDA line is stable-low during the high period of
the Acknowledge-related clock pulse. Of course, setup
and hold times must be taken into account. During
reads, a master must signal an end of data to the slave
by NOT generating an Acknowledge bit on the last byte
that has been clocked out of the slave. In this case, the
slave (MCP7940X) will leave the data line high to
enable the master to generate the Stop condition.
FIGURE 4-1:
DATA TRANSFER SEQUENCE ON THE SERIAL BUS
Note:
The MCP7940X does not generate any
Acknowledge bits while an internal Unique
ID programming cycle is in progress, but
the user may still access the SRAM and
RTCC registers.
Address or
Acknowledge
Valid
Data
Allowed
to Change
Stop
Condition
Start
Condition
SCL
SDA
(A)
(B)
(D)
(C)
(A)
鐩搁棞(gu膩n)PDF璩囨枡
PDF鎻忚堪
VI-J4F-MZ CONVERTER MOD DC/DC 72V 25W
MS3452W24-22SW CONN RCPT 4POS BOX MNT W/SCKT
MCP79400T-I/MS IC RTCC 64B SRAM GP I2C 8MSOP
MS3452L24-22S CONN RCPT 4POS BOX MNT W/SCKT
MCP4141-104E/P IC POT DGTL SNGL 100K SPI 8DIP
鐩搁棞(gu膩n)浠g悊鍟�/鎶€琛�(sh霉)鍙冩暩(sh霉)
鍙冩暩(sh霉)鎻忚堪
MCP79401 鍒堕€犲晢:MICROCHIP 鍒堕€犲晢鍏ㄧū:Microchip Technology 鍔熻兘鎻忚堪:I2C? Real-Time Clock/Calendar with SRAM, Unique ID and Battery Switchover
MCP79401-I/MS 鍔熻兘鎻忚堪:瀵�(sh铆)鏅�(sh铆)鏅�(sh铆)閻� I2C GP RTCC 64B SRAM EUI-48 RoHS:鍚� 鍒堕€犲晢:Microchip Technology 鍔熻兘:Clock, Calendar. Alarm RTC 绺界窔鎺ュ彛:I2C 鏃ユ湡鏍煎紡:DW:DM:M:Y 鏅�(sh铆)闁撴牸寮�:HH:MM:SS RTC 瀛樺劜(ch菙)瀹归噺:64 B 闆绘簮闆诲-鏈€澶�:5.5 V 闆绘簮闆诲-鏈€灏�:1.8 V 鏈€澶у伐浣滄韩搴�:+ 85 C 鏈€灏忓伐浣滄韩搴�: 瀹夎棰�(f膿ng)鏍�:Through Hole 灏佽 / 绠遍珨:PDIP-8 灏佽:Tube
MCP79401-I/SN 鍔熻兘鎻忚堪:瀵�(sh铆)鏅�(sh铆)鏅�(sh铆)閻� I2C GP RTCC 64B SRAM EUI-48 RoHS:鍚� 鍒堕€犲晢:Microchip Technology 鍔熻兘:Clock, Calendar. Alarm RTC 绺界窔鎺ュ彛:I2C 鏃ユ湡鏍煎紡:DW:DM:M:Y 鏅�(sh铆)闁撴牸寮�:HH:MM:SS RTC 瀛樺劜(ch菙)瀹归噺:64 B 闆绘簮闆诲-鏈€澶�:5.5 V 闆绘簮闆诲-鏈€灏�:1.8 V 鏈€澶у伐浣滄韩搴�:+ 85 C 鏈€灏忓伐浣滄韩搴�: 瀹夎棰�(f膿ng)鏍�:Through Hole 灏佽 / 绠遍珨:PDIP-8 灏佽:Tube
MCP79401-I/ST 鍔熻兘鎻忚堪:瀵�(sh铆)鏅�(sh铆)鏅�(sh铆)閻� I2C GP RTCC 64B SRAM EUI-48 RoHS:鍚� 鍒堕€犲晢:Microchip Technology 鍔熻兘:Clock, Calendar. Alarm RTC 绺界窔鎺ュ彛:I2C 鏃ユ湡鏍煎紡:DW:DM:M:Y 鏅�(sh铆)闁撴牸寮�:HH:MM:SS RTC 瀛樺劜(ch菙)瀹归噺:64 B 闆绘簮闆诲-鏈€澶�:5.5 V 闆绘簮闆诲-鏈€灏�:1.8 V 鏈€澶у伐浣滄韩搴�:+ 85 C 鏈€灏忓伐浣滄韩搴�: 瀹夎棰�(f膿ng)鏍�:Through Hole 灏佽 / 绠遍珨:PDIP-8 灏佽:Tube
MCP79401T-I/MNY 鍔熻兘鎻忚堪:瀵�(sh铆)鏅�(sh铆)鏅�(sh铆)閻� I2C GP RTCC 64B SRAM EUI-48 RoHS:鍚� 鍒堕€犲晢:Microchip Technology 鍔熻兘:Clock, Calendar. Alarm RTC 绺界窔鎺ュ彛:I2C 鏃ユ湡鏍煎紡:DW:DM:M:Y 鏅�(sh铆)闁撴牸寮�:HH:MM:SS RTC 瀛樺劜(ch菙)瀹归噺:64 B 闆绘簮闆诲-鏈€澶�:5.5 V 闆绘簮闆诲-鏈€灏�:1.8 V 鏈€澶у伐浣滄韩搴�:+ 85 C 鏈€灏忓伐浣滄韩搴�: 瀹夎棰�(f膿ng)鏍�:Through Hole 灏佽 / 绠遍珨:PDIP-8 灏佽:Tube