參數資料
型號： MCP73832
廠商： Microchip Technology Inc.
英文描述： Miniature Single-Cell, Fully Integrated Li-Ion, Li-Polymer Charge Management Controllers
中文描述： 微型單細胞，完全集成的鋰離子電池，鋰聚合物充電管理控制器
文件頁數： 10/24頁
文件大?。?/td> 696K
代理商： MCP73832
MCP73831/2
DS21984B-page 10
2006 Microchip Technology Inc.
4.0
DEVICE OVERVIEW
The MCP73831/2 are highly advanced linear charge
management controllers. Figure 4-1 depicts the
operational flow algorithm from charge initiation to
completion and automatic recharge.
FIGURE 4-1:
Flowchart.
4.1
Under Voltage Lockout (UVLO)
An internal UVLO circuit monitors the input voltage
and keeps the charger in Shutdown mode until the
input supply rises above the UVLO threshold. The
UVLO circuitry has a built in hysteresis of 100 mV.
In the event a battery is present when the input power
is applied, the input supply must rise 150 mV above
the battery voltage before the MCP73831/2 becomes
operational.
The UVLO circuit places the device in Shutdown mode
if the input supply falls to within +50 mV of the battery
voltage. Again, the input supply must rise to a level
150 mV above the battery voltage before the
MCP73831/2 become operational.
The UVLO circuit is always active. At any time the
input supply is below the UVLO threshold or within
+50 mV of the voltage at the V
BAT
pin, the
MCP73831/2 are placed in a Shutdown mode.
During any UVLO condition, the battery reverse
discharge current shall be less than 2
μ
A.
4.2
Charge Qualification
For a charge cycle to begin, all UVLO conditions must
be met and a battery or output load must be present. A
charge current programming resistor must be
connected from PROG to V
SS
. If the PROG pin is
open or floating, the MCP73831/2 are disabled and
the battery reverse discharge current is less than 2
μ
A.
In this manner, the PROG pin acts as a charge enable
and can be used as a manual shutdown.
4.3
Preconditioning
If the voltage at the V
BAT
pin is less than the precondi-
tioning threshold, the MCP73831/2 enter a precondi-
tioning or Trickle Charge mode. The preconditioning
threshold is factory set. Refer to
Section 1.0 “Electri-
cal Characteristics”
for preconditioning threshold
options and the Product Identification System for
standard options.
In this mode, the MCP73831/2 supply a percentage of
the charge current (established with the value of the
resistor connected to the PROG pin) to the battery.
The percentage or ratio of the current is factory set.
Refer to
Section 1.0 “Electrical Characteristics”
for
preconditioning current options and the Product
Identification System for standard options.
When the voltage at the V
BAT
pin rises above the
preconditioning threshold, the MCP73831/2 enter the
Constant-Current or Fast Charge mode.
4.4
Fast Charge Constant-Current
Mode
During the Constant-Current mode, the programmed
charge current is supplied to the battery or load. The
charge current is established using a single resistor
from PROG to V
SS
. Constant-Current mode is
maintained until the voltage at the V
BAT
pin reaches
the regulation voltage, V
REG
.
SHUTDOWN MODE
V
DD
< V
UVLO
V
DD
< V
BAT
or
PROG > 200 k
Ω
STAT = Hi-Z
PRECONDITIONING
MODE
Charge Current = I
PREG
STAT = LOW
FAST CHARGE
MODE
Charge Current = I
REG
STAT = LOW
CONSTANT VOLTAGE
MODE
Charge Voltage = V
REG
STAT = LOW
V
BAT
< V
PTH
V
BAT
> V
PTH
V
BAT
= V
REG
V
BAT
< V
RTH
V
BAT
> V
PTH
I
BAT
< I
TERM
CHARGE COMPLETE
MODE
No Charge Current
STAT = HIGH (MCP73831)
STAT = Hi-Z (MCP73832)
相關PDF資料
PDF描述
MCP73842 FPGA - 200000 SYSTEM GATE 2.5 VOLT - NOT RECOMMENDED for NEW DESIGN
MCP73841 Advanced Single or Dual Cell Lithium-Ion/ Lithium-Polymer Charge Management Controllers
MCP73844 Advanced Single or Dual Cell Lithium-Ion/ Lithium-Polymer Charge Management Controllers
MCP73843 Advanced Single or Dual Cell Lithium-Ion/ Lithium-Polymer Charge Management Controllers
MCP73861 Advanced Single Cell, Fully Integrated Li-Ion /Li-Polymer Charge Management Controllers(增強型單節高度集成的鋰離子/鋰聚合物充電管理控制器)
相關代理商/技術參數
參數描述
MCP73832-2ACI/MC 功能描述:電池管理 Li-Ion/Li-Poly Charg Mgnt 4.2V Vreg out RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
MCP73832-2ACI/OT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Miniature Single-Cell, Fully Integrated Li-Ion, Li-Polymer Charge Management Controllers
MCP73832-2ADI/MC 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Miniature Single-Cell, Fully Integrated Li-Ion, Li-Polymer Charge Management Controllers
MCP73832-2ADI/OT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Miniature Single-Cell, Fully Integrated Li-Ion, Li-Polymer Charge Management Controllers
MCP73832-2ATI/MC 功能描述:電池管理 Li-Ion/Li-Poly Charg Mgnt 4.2V Vreg out RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*