I2C" />
參數資料
型號: MCP4662T-503E/UN
廠商: Microchip Technology
文件頁數: 6/92頁
文件大小: 0K
描述: IC POT DGTL 50K DUAL 10-MSOP
標準包裝: 2,500
接片: 257
電阻(歐姆): 50k
電路數: 2
溫度系數: 標準值 150 ppm/°C
存儲器類型: 非易失
接口: I²C(設備位址)
電源電壓: 2.7 V ~ 5.5 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 10-TFSOP,10-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 10-MSOP
包裝: 帶卷 (TR)
MCP454X/456X/464X/466X
DS22107A-page 14
2008 Microchip Technology Inc.
FIGURE 1-2:
I2C Bus Data Timing.
90
91
92
100
101
103
106
107
109
110
102
SCL
SDA
In
SDA
Out
TABLE 1-2:
I2C BUS DATA REQUIREMENTS (SLAVE MODE)
I2C AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
–40
°C ≤ TA ≤ +125°C (Extended)
Operating Voltage VDD range is described in AC/DC characteristics
Param.
No.
Sym
Characteristic
Min
Max
Units
Conditions
100
THIGH
Clock high time
100 kHz mode
4000
ns
1.8V-5.5V
400 kHz mode
600
ns
2.7V-5.5V
1.7 MHz mode
120
ns
4.5V-5.5V
3.4 MHz mode
60
ns
4.5V-5.5V
101
TLOW
Clock low time
100 kHz mode
4700
ns
1.8V-5.5V
400 kHz mode
1300
ns
2.7V-5.5V
1.7 MHz mode
320
ns
4.5V-5.5V
3.4 MHz mode
160
ns
4.5V-5.5V
Note 1:
As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region
(minimum 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions.
2:
A fast-mode (400 kHz) I2C-bus device can be used in a standard-mode (100 kHz) I2C-bus system, but the
requirement tSU;DAT ≥ 250 ns must then be met. This will automatically be the case if the device does not
stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal,
it must output the next data bit to the SDA line
TR max.+tSU;DAT = 1000 + 250 = 1250 ns (according to the standard-mode I
2C bus specification) before
the SCL line is released.
3:
The MCP46X1/MCP46X2 device must provide a data hold time to bridge the undefined part between VIH
and VIL of the falling edge of the SCL signal. This specification is not a part of the I
2C specification, but
must be tested in order to ensure that the output data will meet the setup and hold specifications for the
receiving device.
4:
Use Cb in pF for the calculations.
5:
Not Tested
6:
A Master Transmitter must provide a delay to ensure that difference between SDA and SCL fall times do
not unintentionally create a Start or Stop condition.
7:
Ensured by the TAA 3.4 MHz specification test.
相關PDF資料
PDF描述
DS1306EN IC RTC SERIAL ALARM IND 20-TSSOP
DS1306E IC RTC SERIAL ALARM 20-TSSOP
DS1284 IC TIMEKEEPER WATCHDOG 28-DIP
DS17887-5 IC RTC 5V 8K NV RAM 24-EDIP
MCP4662T-104E/UN IC POT DGTL 100K DUAL 10-MSOP
相關代理商/技術參數
參數描述
MCP46XXDM-PTPLS 功能描述:數字電位計 IC MCP46XX PICtail Plus Daughter Board RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
MCP46XXEV 功能描述:數字電位計開發工具 MCP46XX Eval Board RoHS:否 制造商:Arduino 產品:TinkerKit Rotary Potentiometers 工具用于評估:TinkerKit 電阻:4.7 kOhms 工作電源電壓:0 V to 5 V
MCP4706A0T-015E/CH 制造商:Microchip Technology Inc 功能描述:IC, DAC, 16 bit, 3.4 MSPS, SOT-23-6; Resolution (Bits):8bit; Input Channel Type:Single Ended; Supply Voltage Range:2.7V to 5.5V; Digital IC Case Style:SOT-23; No. of Pins:6; Data Interface:I2C, Serial; Supply Current:210A
MCP4706A0T-E/CH 功能描述:數模轉換器- DAC Sngl 8B NV DAC w/Ext Vref & I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MCP4706A0T-E/MAY 功能描述:數模轉換器- DAC Sngl 8B NV DAC w/Ext Vref & I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube