參數資料
型號: MCP40D18T-503AE/LT
廠商: Microchip Technology
文件頁數: 36/43頁
文件大?。?/td> 0K
描述: IC POT 7BIT 50K I2C SC-70-6
標準包裝: 3,000
接片: 128
電阻(歐姆): 50k
電路數: 1
溫度系數: 標準值 150 ppm/°C
存儲器類型: 易失
接口: I²C
電源電壓: 1.8 V ~ 5.5 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 6-TSSOP(5 引線),SC-88A,SOT-353
供應商設備封裝: SC-70-5
包裝: 帶卷 (TR)
2009 Microchip Technology Inc.
DS22152B-page 41
MCP40D17/18/19
6.0
RESISTOR NETWORK
The Resistor Network is made up of two parts. These
are:
Resistor Ladder
Wiper
Figure 6-1 shows a block diagram for the resistive
network.
Digital potentiometer applications can be divided into
two resistor network categories:
Rheostat configuration
Potentiometer (or voltage divider) configuration
The MCP40D17 is a true rheostat, with terminal B and
the wiper (W) of the variable resistor available on pins.
The MCP40D18 device offers a voltage divider
(potentiometer) with terminal B internally connected to
ground.
The MCP40D19 device is a Rheostat device with
terminal A of the resistor floating, terminal B internally
connected to ground, and the wiper (W) available on
pin.
6.1
Resistor Ladder Module
The resistor ladder is a series of equal value resistors
(RS) with a connection point (tap) between the two
resistors. The total number of resistors in the
series (ladder)
determines
the
RAB
resistance
(see Figure 6-1). The end points of the resistor ladder
are connected to the device Terminal A and Terminal B
pins. The RAB (and RS) resistance has small variations
over voltage and temperature.
The Resistor Network has 127 resistors in a string
between terminal A and terminal B. This gives 7-bits of
resolution.
The wiper can be set to tap onto any of these 127
resistors
thus
providing
128
possible
settings
(including terminal A and terminal B). This allows zero
scale to full scale connections.
A wiper setting of 00h connects the Terminal W (wiper)
to Terminal B (Zero Scale). A wiper setting of 3Fh is the
Mid scale setting. A wiper setting of 7Fh connects
the Terminal W (wiper) to Terminal A (Full Scale).
Table 6-1 illustrates the full wiper setting map.
Terminal A and B as well as the wiper W do not have a
polarity. These terminals can support both positive and
negative current.
FIGURE 6-1:
Resistor Network Block
Diagram.
TABLE 6-1:
WIPER SETTING MAP
Wiper Setting
Properties
07Fh
Full Scale (W = A)
07Eh - 040h
W = N
03Fh
W = N (Mid Scale)
03Eh - 001h
W = N
000h
Zero Scale (W = B)
RS
A
RS
B
N = 127
N = 126
N = 125
N = 1
N = 0
RW (1)
W
01h
Analog
Mux
RW (1)
00h
RW (1)
7Dh
RW (1)
7Eh
RW (1)
7Fh
Note 1: The wiper resistance is tap dependent.
That is, each tap selection resistance
has a small variation. This variation has
more effect on devices with smaller RAB
resistance (5.0 k
Ω).
相關PDF資料
PDF描述
MCP42100T-E/ST IC POT DGTL 100K 2CH SPI 14TSSOP
MCP4251-503E/P IC DGTL POT 50K 2CH 14DIP
MCP4261-104E/P IC POT DGTL DUAL 100K SPI 14DIP
MCP4351-502E/ML IC DGTL POT QUAD 5K 20QFN
MCP4361-503E/ML IC POT 8BIT QUAD 50K 20QFN
相關代理商/技術參數
參數描述
MCP40D18T-503E/LT 功能描述:數字電位計 IC 50k I2C sngl 7-bit volatile memory RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
MCP40D19 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7-Bit Single I2C? (with Command Code) Digital POT with Volatile Memory in SC70
MCP40D19-103AE/LT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7-Bit Single I2C? (with Command Code) Digital POT with Volatile Memory in SC70
MCP40D19-103E/LT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7-Bit Single I2C? (with Command Code) Digital POT with Volatile Memory in SC70
MCP40D19-104AE/LT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7-Bit Single I2C? (with Command Code) Digital POT with Volatile Memory in SC70