參數資料
型號: MCP3423EV
廠商: Microchip Technology
文件頁數: 10/58頁
文件大?。?/td> 0K
描述: BOARD EVAL 18BIT 2CH ADC MCP3423
產品培訓模塊: MCP3901 Analog Front End
標準包裝: 1
ADC 的數量: 1
位數: 18
采樣率(每秒): 3.75
數據接口: 串行
輸入范圍: ±VREF
工作溫度: -40°C ~ 125°C
已用 IC / 零件: MCP3423
已供物品:
產品目錄頁面: 672 (CN2011-ZH PDF)
相關產品: MCP3423T-E/UNTR-ND - IC ADC 18BIT 3.75SPS 2CH 10-MSOP
MCP3423T-E/MFTR-ND - IC ADC 18BIT 3.75SPS 2CH 10-DFN
MCP3423-E/UN-ND - IC ADC 18BIT 3.75SPS 2CH 10-MSOP
MCP3423-E/MF-ND - IC ADC 18BIT 3.75SPS 2CH 10-DFN
MCP3422/3/4
DS22088C-page 18
2009 Microchip Technology Inc.
5.2
Configuration Register
The device has an 8-bit wide configuration register to
select for: input channel, conversion mode, conversion
rate, and PGA gain. This register allows the user to
change the operating condition of the device and check
the status of the device operation.
The user can rewrite the configuration byte any time
during the device operation. Register 5-1 shows the
configuration register bits.
REGISTER 5-1:
CONFIGURATION REGISTER
R/W-1
R/W-0
R/W-1
R/W-0
RDY
C1
C0
O/C
S1
S0
G1
G0
1 *
0 *
1 *
0 *
bit 7
bit 0
* Default Configuration after Power-On Reset
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
RDY: Ready Bit
This bit is the data ready flag. In read mode, this bit indicates if the output register has been updated
with a latest conversion result. In One-Shot Conversion mode, writing this bit to “1” initiates a new
conversion.
Reading RDY bit with the read command:
1
= Output register has not been updated
0
= Output register has been updated with the latest conversion result
Writing RDY bit with the write command:
Continuous Conversion mode: No effect
One-Shot Conversion mode:
1
= Initiate a new conversion
0
= No effect
bit 6-5
C1-C0: Channel Selection Bits
00
=
Select Channel 1 (Default)
01
=
Select Channel 2
10
=
Select Channel 3 (MCP3424 only, treated as “00” by the MCP3422/MCP3423)
11
=
Select Channel 4 (MCP3424 only, treated as “01” by the MCP3422/MCP3423)
bit 4
O/C: Conversion Mode Bit
1
= Continuous Conversion Mode (Default). The device performs data conversions continuously
0
= One-Shot Conversion Mode. The device performs a single conversion and enters a low power
standby mode until it receives another write or read command
bit 3-2
S1-S0: Sample Rate Selection Bit
00
=
240 SPS (12 bits) (Default)
01
=
60 SPS (14 bits)
10
=
15 SPS (16 bits)
11
=
3.75 SPS (18 bits)
bit 1-0
G1-G0: PGA Gain Selection Bits
00
=x1 (Default)
01
=x2
10
=x4
11
=x8
相關PDF資料
PDF描述
CDB5571 DEV BOARD FOR CS5571 W/MUX
UPB2C821MRD CAP ALUM 820UF 160V 20% RADIAL
LLS2D561MELZ CAP ALUM 560UF 200V 20% SNAP
EEC22DRTH-S93 CONN EDGECARD 44POS DIP .100 SLD
MCP3425EV EVALUATION BOARD FOR MCP3425
相關代理商/技術參數
參數描述
MCP3423T-E/MC 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit, Multi-Channel ???£ Analog-to-Digital Converter with I2Ca?¢ Interface and On-Board Reference
MCP3423T-E/MF 功能描述:模數轉換器 - ADC 18B delta-sigma ADC dual Ch 4sps RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MCP3423T-E/MS 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit, Multi-Channel ???£ Analog-to-Digital Converter with I2Ca?¢ Interface and On-Board Reference
MCP3423T-E/SL 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit, Multi-Channel ???£ Analog-to-Digital Converter with I2Ca?¢ Interface and On-Board Reference
MCP3423T-E/SN 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit, Multi-Channel ???£ Analog-to-Digital Converter with I2Ca?¢ Interface and On-Board Reference