- 您現在的位置：買賣IC網 > PDF目錄17041 > MCP3421EV (Microchip Technology)BOARD EVAL FOR MCP3421 SOT23-6 PDF資料下載
參數資料
| 型號： | MCP3421EV |
| 廠商： | Microchip Technology |
| 文件頁數： | 7/42頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR MCP3421 SOT23-6 |
| 產品培訓模塊： | MCP3901 Analog Front End |
| 設計資源： | MCP3421EV Gerber Files |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 18 |
| 采樣率（每秒）： | 4 |
| 數據接口： | 串行 |
| 輸入范圍： | ±2.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 已用 IC / 零件： | MCP3421 |
| 已供物品： | 2 板，CD |
| 產品目錄頁面： | 672 (CN2011-ZH PDF) |
| 相關產品： | MCP3421A5T-E/OTDKR-ND - IC ADC 18BIT 3.75SPS SOT23-6 MCP3421A3T-E/CHTR-ND - IC ADC 18BIT 3.75SPS 1CH SOT23-6 MCP3421A2T-E/CHTR-ND - IC ADC 18BIT 3.75SPS 1CH SOT23-6 MCP3421A1T-E/CHTR-ND - IC ADC 18BIT 3.75SPS 1CH SOT23-6 MCP3421A0T-E/CHTR-ND - IC ADC 18BIT 3.75SPS 1CH SOT23-6 MCP3421A0T-E/OTDKR-ND - IC ADC 18BIT 3.75SPS 1CH SOT23-6 MCP3421A0T-E/OTCT-ND - IC ADC 18BIT 3.75SPS 1CH SOT23-6 MCP3421A0T-E/OTTR-ND - IC ADC 18BIT 3.75SPS 1CH SOT23-6 MCP3421A5T-E/OTCT-ND - IC ADC 18BIT 3.75SPS SOT23-6 MCP3421A5T-E/OTTR-ND - IC ADC 18BIT 3.75SPS SOT23-6 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
2009 Microchip Technology Inc.
DS22003E-page 15
MCP3421
5.0
USING THE MCP3421 DEVICE
5.1
Operating Modes
The user operates the device by setting up the device
configuration register using a write command (see
Figure 5-2) and reads the conversion data using a read
command (see Figure 5-3 and Figure 5-4). The device
operates in two modes: (a) Continuous Conversion
Mode or (b) One-Shot Conversion Mode (single
conversion). This mode selection is made by setting
the O/C bit in the Configuration Register. Refer to
Section 5.2 “Configuration Register” for more
information.
5.1.1
CONTINUOUS CONVERSION
MODE (O/C BIT = 1)
The device performs a Continuous Conversion if the
O/C bit is set to logic “high”. Once the conversion is
completed, RDY bit is toggled to ‘0’ and the result is
placed at the output data register. The device
immediately begins another conversion and overwrites
the output data register with the most recent result. The
device clears the data ready flag (RDY bit = 0) when
the conversion is completed. The device sets the ready
flag bit (RDY bit = 1), if the latest conversion result has
been read by the Master.
When writing configuration register:
- Setting RDY bit in continuous mode does not
affect anything
When reading conversion data:
- RDY bit = 0 means the latest conversion
result is ready
- RDY bit = 1 means the conversion result is
not updated since the last reading. A new
conversion is under processing and the RDY
bit will be cleared when the new conversion
result is ready
5.1.2
ONE-SHOT CONVERSION MODE
(O/C BIT = 0)
Once the One-Shot Conversion (single conversion)
Mode is selected, the device performs only one
conversion, updates the output data register, clears the
data ready flag (RDY = 0), and then enters a low power
standby mode. A new One-Shot Conversion is started
again when the device receives a new write command
with RDY = 1.
When writing configuration register:
- The RDY bit needs to be set to begin a new
conversion in one-shot mode
When reading conversion data:
- RDY bit = 0 means the latest conversion
result is ready
- RDY bit = 1 means the conversion result is
not updated since the last reading. A new
conversion is under processing and the RDY
bit will be cleared when the new conversion is
done
This
One-Shot
Conversion
Mode
is
highly
recommended for low power operating applications
where the conversion result is needed by request on
demand. During the low current standby mode, the
device consumes less than 1 A maximum (or 300 nA
typical). For example, if the user collects 18 bit
conversion
data
once
a
second
in
One-Shot
Conversion mode, the device draws only about one
fourth of its total operating current. In this example, the
device consumes approximately 39 A (145 A / 3.75
SPS = 39 A), if the device performs only one
conversion per second (1 SPS) in 18-bit conversion
mode with 3V power supply.
相關PDF資料 |
PDF描述 |
|---|---|
| GEC44DRES-S13 | CONN EDGECARD 88POS .100 EXTEND |
| MCP3422EV | BOARD EVAL MCP3422 PICKIT SERIAL |
| RBC10DRXN-S734 | CONN EDGECARD 20POS DIP .100 SLD |
| REC5-053.3DRW/H2/C | CONV DC/DC 5W 4.5-9VIN +/-3.3V |
| RBC10DRXH-S734 | CONN EDGECARD 20POS DIP .100 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP3422 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit, Multi-Channel ???￡ Analog-to-Digital Converter with I2Ca?￠ Interface and On-Board Reference |
| MCP3422A0-E/MC | 功能描述:模數轉換器 - ADC 18B delta-sigma ADC dual Ch 4sps RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3422A0-E/MF | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit, Multi-Channel ???￡ Analog-to-Digital Converter with I2Ca?￠ Interface and On-Board Reference |
| MCP3422A0-E/MS | 功能描述:模數轉換器 - ADC 18B delta-sigma ADC dual Ch 4sps RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3422A0-E/SL | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit, Multi-Channel ???￡ Analog-to-Digital Converter with I2Ca?￠ Interface and On-Board Reference |
發布緊急采購，3分鐘左右您將得到回復。