參數資料
型號： MCP2200-I/MQ
廠商： Microchip Technology
文件頁數： 40/44頁
文件大小： 0K
描述： IC USB TO UART 20QFN
特色產品： MCP2200 USB-to-UART Serial Converter
標準包裝： 73
特點： USB 至 UART
通道數： 8
FIFO's： 256 字節
規程： USB 2.0
電源電壓： 3 V ~ 5.5 V
帶自動流量控制功能： 是
安裝類型： 表面貼裝
封裝/外殼： 20-VQFN 裸露焊盤
供應商設備封裝： 20-VQFN
包裝： 管件
產品目錄頁面： 684 (CN2011-ZH PDF)
2011 Microchip Technology Inc.
DS22228B-page 5
MCP2200
EQUATION 1-1:
SOLVING FOR ACTUAL
BAUD RATE
1.3.3
CUSTOM BAUD RATES
Custom baud rates are configured by sending the
SET_LINE_CODING
USB
command, or by using the
information.
1.3.4
HARDWARE FLOW CONTROL
Hardware flow control uses the RTS and CTS pins as
a handshake between two devices. The RTS pin of
one device is typically connected to the CTS of the
other device.
RTS is an active low output that notifies the other
device when it is ready to receive data by driving the pin
low. The MCP2200 trip point for de-asserting RTS
(high) is 63 characters. This is one character short of
“buffer full”.
CTS is an active low input that notifies the MCP2200
when it is ready to send data. The MCP2200 will check
CTS just before loading and sending UART data. If the
pin is asserted during a transfer, the transfer will con-
tinue. Refer to Figure 1.4.
FIGURE 1-1:
RTS/CTS CONNECTIONS
EXAMPLE
1.3.4.1
Flow Control Disabled
The buffer pointer does not increment (or reset to
zero) if the buffer is full. Therefore, if hardware flow
control is not enabled and an overflow occurs (i.e., 65
unprocessed characters received), the new data
overwrites the last position in the buffer.
1.4
USB Protocol Controller
The USB controller in the MCP2200 is full-speed USB
2.0 compliant.
Composite device (CDC + HID):
- CDC: USB-to-UART communications
- HID: I/O control, EEPROM access and initial
configuration
128 byte buffer to handle data throughput at any
UART baud rate:
- 64-byte transmit
-64-byte receive
Fully configurable VID and PID assignments, and
descriptors (stored on-chip)
Bus powered or self-powered
1.4.1
DESCRIPTORS
During configuration, the supplied PC interface stores
the descriptors in the MCP2200.
1.4.2
SUSPEND AND RESUME
The USB Suspend and Resume signals are supported
for power management of the MCP2200. The device
enters Suspend mode when “suspend signaling” is
detected on the bus.
The MCP2200 exits Suspend mode when any of the
following events occur:
1.
“Resume signaling” is detected or generated
2.
A USB “Reset” signal is detected
3.
A device Reset occurs
1.5
USB Transceiver
The MCP2200 has a built-in, USB 2.0, full-speed
transceiver internally connected to the USB module.
The USB transceiver obtains power from the VUSB pin,
which is internally connected to the 3.3V regulator. The
best electrical signal quality is obtained when VUSB is
locally bypassed with a high quality ceramic capacitor.
1.5.1
INTERNAL PULL-UP RESISTORS
The MCP2200 devices have built-in pull-up resistors
designed to meet the requirements for full-speed USB.
1.5.2
MCP2200 POWER OPTIONS
The following are the main power options for the
MCP2200:
USB Bus Powered (5V)
3.3V Self Powered
ActualRate
12MHz
int x
-------------------
=
Where:
x
12MHz
DesiredBaud
-----------------------------------
=
RTS
CTS
I am ready
to receive
I’ll transmit
if okay
I am ready
to receive
I’ll transmit
if okay
MCU
MCP2200
相關PDF資料
PDF描述
MCP2200T-I/MQ IC USB 2.0 - UART 20QFN
MCP2210T-I/MQ IC CONVERTER USB-PCI 20-QFN
MCP23008-E/ML IC I/O EXPANDER I2C 8B 20QFN
MCP23016T-I/ML IC I/O EXPANDER I2C 16B 28QFN
MCP23018T-E/SS IC I/O EXPANDER I2C 16B 24SSOP
相關代理商/技術參數
參數描述
MCP2200-ISO 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:USB 2.0 to UART Protocol Converter with GPIO
MCP2200-ISS 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:USB 2.0 to UART Protocol Converter with GPIO
MCP2200T-I/MQ 功能描述:USB 接口集成電路 USB-to-UART Protocol Converter w/ GPIO RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
MCP2200T-I/NQ 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:USB 2.0 to UART Protocol Converter with GPIO
MCP2200T-I/SO 功能描述:USB 接口集成電路 USB-to-UART Protocol Converter w/ GPIO RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*