- 您現在的位置：買賣IC網 > PDF目錄16672 > MCP2140DM-TMPSNS (Microchip Technology)BOARD DEMO FOR MCP2140 PDF資料下載
參數資料
| 型號： | MCP2140DM-TMPSNS |
| 廠商： | Microchip Technology |
| 文件頁數： | 10/58頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD DEMO FOR MCP2140 |
| 產品培訓模塊： | PIC18 J Series MCU Overview |
| 標準包裝： | 1 |
| 主要目的： | 接口，IrDA |
| 嵌入式： | 是，MCU，8 位 |
| 已用 IC / 零件： | MCP2140 |
| 主要屬性： | 帶 PIC18F MCU 和溫度傳感器的 IrDA 控制器 |
| 次要屬性： | 設置為數據記錄器 |
| 已供物品： | 板，軟件 |
| 產品目錄頁面： | 685 (CN2011-ZH PDF) |
| 相關產品： | MCP2140A-I/SS-ND - IC IRDA CONTROLLR DTE/DCE 20SSOP MCP2140A-I/SO-ND - IC IRDA CONTROLLR DTE/DCE 18SOIC MCP2140A-I/P-ND - IC IRDA CONTROLLR DTE/DCE 18DIP MCP2140AT-I/SSTR-ND - IC IRDA CONTROLLR DTE/DCE 20SSOP MCP2140AT-I/SOTR-ND - IC IRDA CONTROLLR DTE/DCE 18SOIC MCP2140T-I/SS-ND - IC IRDA CONTROLLR DTE/DCE 20SSOP MCP2140T-I/SO-ND - IC IRDA CONTROLLR DTE/DCE 18SOIC MCP2140-I/SS-ND - IC IRDA CONTROLLR DTE/DCE 20SSOP MCP2140-I/SO-ND - IC IRDA CONTROLLR DTE/DCE 18SOIC MCP2140-I/P-ND - IC IRDA CONTROLLER DTE/DCE 18DIP |
| 其它名稱： | MCP2140DM-TMPSNSR MCP2140DM-TMPSNSR-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
MCP2140
DS21790A-page 18
Preliminary
2003 Microchip Technology Inc.
2.14
How The MCP2140 Connects
When two devices, implementing the IrDA standard
feature, establish a connection using the IrCOMM pro-
tocol, the process is analogous to connecting two
devices with serial ports using a cable. This is referred
to as a “point-to-point” connection. This connection is
limited to half-duplex operation because the IR trans-
ceiver cannot transmit and receive at the same time.
The purpose of the IrDA standard protocol is to allow
this half-duplex link to emulate, as much as possible, a
full-duplex connection. In general, this is done by divid-
ing the data into “packets”, or groups of data. These
packets can be sent back and forth, when needed,
without risk of collision. The rules of how and when
these packets are sent constitute the IrDA standard
protocol. The MCP2140 supports elements of this IrDA
standard protocol to communicate with other IrDA stan-
dard compatible devices.
When a wired connection is used, the assumption is
made that both sides have the same communications
parameters and features. A wired connection has no
need to identify the other connector because it is
assumed that the connectors are properly connected.
According to the IrDA standard, a connection process
has been defined to identify other IrDA standard com-
patible devices and establish a communication link.
There are three steps that these two devices go
through to make this connection. They are:
Normal Disconnect Mode (NDM)
Discovery Mode
Normal Connect Mode (NCM)
Figure 2-13 shows the connection sequence.
2.14.1
NORMAL DISCONNECT MODE
(NDM)
When two IrDA standard compatible devices come into
range, they must first recognize each other. The basis
of this process is that one device has some task to
accomplish and the other device has a resource
needed to accomplish this task. One device is referred
to as a Primary device while the other is referred to as
a Secondary device. The distinction between Primary
device and Secondary device is important because it is
the responsibility of the Primary device to provide the
mechanism to recognize other devices. So the Primary
device must first poll for nearby IrDA standard compat-
ible devices and, during this polling, the default baud
rate of 9600 baud is used by both devices.
For example, if you want to print from an IrDA-equipped
laptop to an IrDA-equipped printer, utilizing the IrDA
standard feature, you would first bring your laptop in
range of the printer. In this case, the laptop is the one
that has something to do and the printer has the
resource to do it. Thus, the laptop is called the Primary
device and the printer is the Secondary device. Some
data-capable cellphones have IrDA standard infrared
ports. If you used such a cell phone with a Personal
Digital Assistant (PDA), the PDA that supports the IrDA
standard feature would be the Primary device and the
cell phone would be the Secondary device.
When a Primary device polls for another device, a
nearby Secondary device may respond. When a Sec-
ondary device responds, the two devices are defined to
be in the Normal Disconnect Mode (NDM) state. NDM
is established by the Primary device broadcasting a
packet and waiting for a response. These broadcast
packets are numbered. Usually, 6 or 8 packets are
sent. The first packet is number 0, while the last packet
is usually numbered 5 or 7. Once all the packets are
sent, the Primary device sends an ID packet, which is
not numbered.
The Secondary device waits for these packets and then
responds to one of the packets. The packet responds
to determine the “timeslot” to be used by the Secondary
device. For example, if the Secondary device responds
after packet number 2, the Secondary device will use
timeslot 2. If the Secondary device responds after
packet number 0, the Secondary device will use
timeslot 0. This mechanism allows the Primary device
to recognize as many nearby devices as there are
timeslots. The Primary device will continue to generate
timeslots and the Secondary device should continue to
respond, even if there’s nothing to do.
During NDM, the MCP2140 handles all responses to
the Primary device (Figure 2-13) without any communi-
cation with the Host Controller. The Host Controller is
inhibited by the CTS signal of the MCP2140 from
sending data to the MCP2140.
Note 1: The MCP2140 can only be used to
implement a Secondary device.
2: The MCP2140 supports a system with
only one Secondary device having
exclusive use of the IrDA standard infra-
red
link
(known as
“point-to-point”
communication).
3: The MCP2140 always responds to packet
number 0. This means that the MCP2140
will always use timeslot 0.
4: If another Secondary device is nearby,
the Primary device may fail to recognize
the MCP2140, or the Primary device may
not recognize either of the devices.
相關PDF資料 |
PDF描述 |
|---|---|
| H8MMS-5006M | DIP CABLE - HDM50S/AE50M/HDM50S |
| VE-B20-EW | CONVERTER MOD DC/DC 5V 100W |
| GCB10DHFT | CONN CARDEDGE 20POS .050" SMD |
| RMW-10/3-1200/ADH-0 | HEAT SHRINK TUBING |
| RNF-100-1/2-BK-STK | HEATSHRINK RNF-100 1/2"X4' BLK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP2140-I/P | 功能描述:網絡控制器與處理器 IC 9600bd fixd spd IrDA RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCP2140-I/P | 制造商:Microchip Technology Inc 功能描述:IrDA Protocol Handler Communication IC |
| MCP2140-I/SO | 功能描述:網絡控制器與處理器 IC 9600bd fixd spd IrDA RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCP2140-I/SO | 制造商:Microchip Technology Inc 功能描述:IrDA Protocol Handler Communication IC |
| MCP2140-I/SS | 功能描述:網絡控制器與處理器 IC 9600bd fixd spd IrDA RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。