- 您現在的位置：買賣IC網 > PDF目錄383588 > MCP201 (Microchip Technology Inc.) LIN Transceiver with Voltage Regulator(帶有集成Vreg的線收發器) PDF資料下載
參數資料
| 型號： | MCP201 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | LIN Transceiver with Voltage Regulator(帶有集成Vreg的線收發器) |
| 中文描述： | LIN收發器和穩壓器（帶有集成Vreg的線收發器） |
| 文件頁數： | 7/27頁 |
| 文件大?。?/td> | 417K |
| 代理商： | MCP201 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
2003 Microchip Technology Inc.
Preliminary
DS21730C-page 7
1.5.7
FAULT/SLPS
FAULT Detect Output, Slope Select Input.
This pin is usually in Output mode. Its state is defined
as shown in Table 1-5.
The state of this pin is internally sampled during power-
on of V
BAT
. Once V
BAT
has reached a stable level
(approx. 6 VDC) and V
REG
is stable at 4.75-5.25 VDC,
the state of this pin selects which slew rate profile to
apply to the LIN output. It is only during this time that
the pin is used as an input (the output driver is off dur-
ing this time). The slope will stay selected until the next
V
BAT
power-off/power-on sequence, regardless of any
power-down, wake-up or SLEEP events. Only a V
BAT
rising state will cause a sampling of the FAULT/SLPS
pin. The Slope selection will be made irrespective of
the state of any other pin.
The FAULT/SLPS pin is connected to either V
REG
or
V
SS
through a (approx. 100 k
) resistor to make the
slope selection. This large resistance allows the FAULT
indication function to overdrive the resistor in normal
operation mode.
If the FAULT/SLPS is high (‘
1
’), the normal slope shap-
ing is selected (dv/dt = 2 V/μs). If FAULT/SLPS is low
(‘
0
’) during this time, the alternate slope shaping is
selected (dv/dt = 4 V/μs)
TABLE 1-4:
FAULT/SLPS SLOPE
SELECTION DURING POR
TABLE 1-5:
FAULT/SLPS TRUTH TABLE
FAULT/SLPS
Slope Shaping
H
L
Normal
Alternate
(1)
Note 1:
This mode does not conform to LIN bus
specification Ver. 1.3.
Note:
This pin is ‘
0
’ whenever the internal circuits
have detected a short or thermal excursion
and have disabled the LIN output driver.
Note:
Every time TX is toggled, a Fault condition
will occur for the length of time, depending
on the bus load. The Fault time is equal to
the propagation delay.
TXD In
RXD Out
LIN bus I/O
Thermal
Override
FAULT/SLPS Out
Comments
L
H
L
H
x
H
H
L
L
x
V
BAT
V
BAT
GND
GND
V
BAT
OFF
OFF
OFF
OFF
ON
L
H
H
L
L
Bus shorted to battery
Bus recessive
Bus dominant
Bus shorted to ground
Thermal excursion
Legend:
x = don’t care
相關PDF資料 |
PDF描述 |
|---|---|
| MCP2120 | low-cost, high-performance, fully-static infrared encoder/decoder.(帶有硬件/軟件波特率選擇的UART到IR編譯碼器) |
| MCP2140 | IrDA Standard Protocol Stack Controller With Fixed 9600 Baud Communication Rate(固定波特率,低成本,IrDA標準協議編譯碼器) |
| MCP2150 | DEVELOPER’S KIT USER’S GUIDE |
| MCP2155 | IrDA Standard Protocol Stack Controller Supporting DCE Applications(提供IrDA協議來處理PLUS位的編碼/譯碼功能,這是為了在一個低引腳的計數設備上實現數據傳輸功能(DCE)而提供的) |
| MCP23016 | 16-Bit I2C I/O Expander(16位I/O口擴展芯片) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP201-E | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:LIN Transceiver with Voltage Regulator |
| MCP201-E/P | 功能描述:LIN 收發器 W/ On Board Vreg RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| MCP201-E/SN | 功能描述:LIN 收發器 W/ On Board Vreg RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| MCP201-EMF | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:LIN Transceiver with Voltage Regulator |
| MCP201-EP | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:LIN Transceiver with Voltage Regulator |
發布緊急采購，3分鐘左右您將得到回復。