參數資料
型號： MCP18480
廠商： Microchip Technology Inc.
元件分類： 基準電壓源/電流源
英文描述： -48V Hot Swap Controller
中文描述： - 48V熱插拔控制器
文件頁數： 35/64頁
文件大?。?/td> 871K
代理商： MCP18480
2003 Microchip Technology Inc.
DS20091B-page 35
MCP18480
TIMER
10
I
A
Current Limit Timer.
The value of the external capacitor (C
TIMER
) connected to the TIMER
pin sets the two time periods used during a current-limit event. These
are:
The time that the GATE pin will limit the current through the
external FET
The time that the GATE pin will disable the external FET
During current limit, a pull-up current source charges up the external
capacitor. Until the voltage on the TIMER pin reaches V
REFIN
/2, the
GATE pin is driven to maintain a reduced current flow determined by
the V
DS
of the external FET.
While the capacitor is being discharged by the pull-down current (pull-
up current is off), the GATE pin is at V
NEG
and the PWRGOOD pin is
deasserted. When the TIMER voltage falls below approximately
100 mV, the GATE pin turns on, if the RESTART pin is low, to reset the
internal fault latch. If the RESTART pin is high, the GATE pin remains
off until the ENABLE pin is forced low. It is then forced high or the
RESTART pin is forced low (asserted).
The PWRGOOD pin reasserts after the voltages on the DRAIN
TH
and
GATE pins meet the appropriate conditions.
The TIMER pin pull-up current is proportioned to the I
ISET
current
(approximately a multiple of 16).
Negative supply input.
V
NEG
11
I
P
The negative voltage applied to the board by the backplane (typically
the most negative voltage in the system).
External MOSFET activation delay.
R
DISCH
12
I
A
An external resistor (R
RDISCH
) is connected between the R
DISCH
pin
and the V
NEG
pin and is used to set the delay between the deactivation
and activation of the external pass MOSFET during a current-limit
event. The delay is set by the values of the external capacitor (C
TIMER
)
and the external resistor (R
RDISCH
). The formulas are:
T
DEACT
= (C
TIMER
x R
ISET
) / 16
T
ACT
= (9.2 x R
RDISCH
x C
TIMER
)
ST = Schmitt Trigger input with CMOS levels
O = Output
CMOS = CMOS-compatible input
D = Digital
TABLE 3-1:
MCP18480 PIN DESCRIPTIONS (CONTINUED)
Pin Name
Pin
Number
Pin
Direction
Buffer
Type
Description
SSOP
Legend: TTL = TTL compatible input
I = Input
P = Power
A = Analog
相關PDF資料
PDF描述
MCP201 LIN Transceiver with Voltage Regulator(帶有集成Vreg的線收發器)
MCP2120 low-cost, high-performance, fully-static infrared encoder/decoder.(帶有硬件/軟件波特率選擇的UART到IR編譯碼器)
MCP2140 IrDA Standard Protocol Stack Controller With Fixed 9600 Baud Communication Rate(固定波特率,低成本,IrDA標準協議編譯碼器)
MCP2150 DEVELOPER’S KIT USER’S GUIDE
MCP2155 IrDA Standard Protocol Stack Controller Supporting DCE Applications(提供IrDA協議來處理PLUS位的編碼/譯碼功能,這是為了在一個低引腳的計數設備上實現數據傳輸功能(DCE)而提供的)
相關代理商/技術參數
參數描述
MCP18480-I/SS 功能描述:熱插拔功率分布 48V Hot Swap RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MCP18480T-I/SS 功能描述:熱插拔功率分布 48V Hot Swap RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
MCP-18H 制造商:Taiyo Electric Ind. 功能描述:
MCP-18-I9-LL 制造商:YAMAICHI 制造商全稱:Yamaichi Electronics Co., Ltd. 功能描述:MatchCon
MCP-18-TI9-LL 制造商:YAMAICHI 制造商全稱:Yamaichi Electronics Co., Ltd. 功能描述:MatchCon
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*