![](http://datasheet.mmic.net.cn/370000/MCP1827T-1202EAB_datasheet_16720922/MCP1827T-1202EAB_8.png)
MCP1827/MCP1827S
DS22001B-page 8
2006 Microchip Technology Inc.
TEMPERATURE SPECIFICATIONS
Electrical Specifications:
Unless otherwise indicated, all limits apply for V
IN
= 2.3V to 6.0V.
Parameters
Sym
Power Supply Ripple Rejection
Ratio
PSRR
—
60
—
dB
f = 100 Hz, C
OUT
= 10 μF,
I
OUT
= 10 mA,
V
INAC
= 30 mV pk-pk,
C
IN
= 0 μF
I
OUT
= 100 μA, V
OUT
= 1.8V,
V
IN
= 2.8V
I
OUT
= 100 μA, V
OUT
= 1.8V,
V
IN
= 2.8V
Thermal Shutdown Temperature
T
SD
—
150
—
°C
Thermal Shutdown Hysteresis
Δ
T
SD
—
10
—
°C
Min
Typ
Max
Units
Conditions
Temperature Ranges
Operating Junction Temperature Range
Maximum Junction Temperature
Storage Temperature Range
Thermal Package Resistances
Thermal Resistance, 5LD DDPAK
Thermal Resistance, 3LD DDPAK
Thermal Resistance, 5LD TO-220
Thermal Resistance, 3LD TO-220
T
J
T
J
T
A
-40
—
-65
—
—
—
+125
+150
+150
°C
°C
°C
Steady State
Transient
θ
JA
θ
JA
θ
JA
θ
JA
—
—
—
—
31.2
31.4
29.3
29.4
—
—
—
—
°C/W
°C/W
°C/W
°C/W
4-Layer JC51 Standard Board
4-Layer JC51 Standard Board
4-Layer JC51 Standard Board
4-Layer JC51 Standard Board
AC/DC CHARACTERISTICS (CONTINUED)
Electrical Specifications:
Unless otherwise noted, V
IN
= V
OUT(MAX)
+ V
DROPOUT(MAX)
Note 1
, V
R
=1.8V for Adjustable Output,
I
OUT
= 1 mA, C
IN
= C
OUT
= 4.7 μF (X7R Ceramic), T
A
= +25°C.
Boldface
type applies for junction temperatures, T
J
(
Note 7
) of
-
40°C to +125°C
Parameters
Sym
Min
Typ
Max
Units
Conditions
Note
1:
2:
The minimum V
IN
must meet two conditions: V
IN
≥
2.3V and V
IN
≥
V
OUT(MAX)
+
V
DROPOUT(MAX).
V
R
is the nominal regulator output voltage for the fixed cases. V
R
= 1.2V, 1.8V, etc. V
R
is the desired set point output
voltage for the adjustable cases. V
R
= V
ADJ
*
((R
1
/R
2
)+1). Figure 4-1.
TCV
OUT
= (V
OUT-HIGH
– V
OUT-LOW
) *10
6
/ (V
R
*
Δ
Temperature). V
OUT-HIGH
is the highest voltage measured over the
temperature range. V
OUT-LOW
is the lowest voltage measured over the temperature range.
Load regulation is measured at a constant junction temperature using low duty-cycle pulse testing. Load regulation is
tested over a load range from 1 mA to the maximum specified output current.
Dropout voltage is defined as the input-to-output voltage differential at which the output voltage drops 2% below its
nominal value that was measured with an input voltage of V
IN =
V
OUTMAX
+ V
DROPOUT(MAX)
.
The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction
temperature and the thermal resistance from junction to air. (i.e., T
A
, T
J
,
θ
JA
). Exceeding the maximum allowable power
dissipation will cause the device operating junction temperature to exceed the maximum +150°C rating. Sustained
junction temperatures above 150°C can impact device reliability.
The junction temperature is approximated by soaking the device under test at an ambient temperature equal to the
desired junction temperature. The test time is small enough such that the rise in the junction temperature over the
ambient temperature is not significant.
3:
4:
5:
6:
7: