- 您現在的位置：買賣IC網 > PDF目錄383585 > MCP1603 (Microchip Technology Inc.) 2.0 MHz, 500 mA Synchronous Buck Regulator PDF資料下載
參數資料
| 型號： | MCP1603 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 2.0 MHz, 500 mA Synchronous Buck Regulator |
| 中文描述： | 2.0兆赫，500毫安同步降壓穩壓器 |
| 文件頁數： | 13/26頁 |
| 文件大?。?/td> | 672K |
| 代理商： | MCP1603 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
2007 Microchip Technology Inc.
DS22042A-page 13
MCP1603
4.3
Soft Start
The output of the MCP1603 is controlled during start-
up. This control allows for a very minimal amount of
V
OUT
overshoot during start-up from V
IN
rising above
the UVLO voltage or SHDN being enabled.
4.4
Overtemperature Protection
Overtemperature protection circuitry is integrated in the
MCP1603. This circuitry monitors the device junction
temperature and shuts the device off, if the junction
temperature exceeds the typical 150°C threshold. If
this threshold is exceeded, the device will automatically
restart once the junction temperature drops by
approximately 10°C. The soft start is reset during an
overtemperture condition.
4.5
Overcurrent Protection
Cycle-by-cycle current limiting is used to protect the
MCP1603 from being damaged when an external short
circuit is applied. The typical peak current limit is
860 mA. If the sensed current reaches the 860 mA
limit, the P-Channel MOSFET is turned off, even if the
output voltage is not in regulation. The device will
attempt to start a new switching cycle when the internal
oscillator sets the internal RS latch.
4.6
Enable/Disable Control
The SHDN pin is used to enable or disable the
MCP1603. When the SHDN pin is pulled low, the
device is disabled. When pulled high the device is
enabled and begins operation provided the input
voltage is not below the UVLO threshold or a fault
condition exists.
4.7
Undervoltage Lockout (UVLO)
The UVLO feature uses a comparator to sense the
input voltage (V
IN
) level. If the input voltage is lower
than the voltage necessary to properly operate the
MCP1603, the UVLO feature will hold the converter off.
When V
IN
rises above the necessary input voltage, the
UVLO is released and soft start begins. Hysteresis is
built into the UVLO circuit to compensate for input
impedance. For example, if there is any resistance
between the input voltage source and the device when
it is operating, there will be a voltage drop at the input
to the device equal to I
IN
x R
IN
. The typical hysteresis
is 140 mV.
相關PDF資料 |
PDF描述 |
|---|---|
| MCP1612 | Single 1A, 1.4 MHz Synchronous Buck Regulator |
| MCP1630V | High-Speed, Microcontroller-Adaptable, Pulse Width Modulator |
| MCP1650REUN | MCP1650 |
| MCP1650SEUN | MCP1650 |
| MCP1651REUN | MCP1650 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP1603_12 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2.0 MHz, 500 mA Synchronous Buck Regulator |
| MCP1603-080I/MC | 制造商:Microchip Technology Inc 功能描述:2.0MHZ, 0.5A, SYNCH-BUCK PFM/PWM REG - Rail/Tube |
| MCP1603-080I/OS | 制造商:Microchip Technology Inc 功能描述:2.0MHZ, 0.5A, SYNCH-BUCK PFM/PWM REG - Rail/Tube |
| MCP1603-120I/MC | 功能描述:開關變換器、穩壓器與控制器 2.0MHz 0.5A SyncBuck PFM PWM Reg RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MCP1603-120I/OS | 制造商:Microchip Technology Inc 功能描述:CONV DC-DC SGL-OUT STEP DOWN 5PIN TSOT - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。