- 您現在的位置：買賣IC網 > PDF目錄383583 > MCP131 (Microchip Technology Inc.) Micropower Voltage Detector PDF資料下載
參數資料
| 型號： | MCP131 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | Micropower Voltage Detector |
| 中文描述： | 微功耗電壓檢測器 |
| 文件頁數： | 11/26頁 |
| 文件大?。?/td> | 266K |
| 代理商： | MCP131 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
2005 Microchip Technology Inc.
DS21889D-page 11
MCP111/112
4.0
APPLICATION INFORMATION
For many of today’s microcontroller applications, care
must be taken to prevent low-power conditions that can
cause many different system problems. The most
common causes are brown-out conditions, where the
system supply drops below the operating level momen-
tarily. The second most common cause is when a slowly
decaying power supply causes the microcontroller to
begin executing instructions without sufficient voltage to
sustain SRAM, thus producing indeterminate results.
Figure 4-1 shows a typical application circuit.
FIGURE 4-1:
Typical Application Circuit.
4.1
V
TRIP
Operation
The voltage trip point (V
) is determined on the falling
edge of V
DD
. The actual voltage trip point (V
TRIPAC
) will
be between the minimum trip point (V
TRIPMIN
) and the
maximum trip point (V
). There is a hysteresis on
this trip point to remove any “jitter” that would occur on
the V
OUT
pin when the device V
DD
is at the trip point.
Figure 4-2 shows the state of the V
OUT
pin as
determined by the V
voltage. The V
specification
is for falling V
DD
voltages. When the V
DD
voltage is
rising, the V
OUT
pin will not be driven high until V
DD
is at
V
TRIP
+ V
HYS
.
FIGURE 4-2:
V
OUT
Operation as Determined by the V
TRIP
and V
HYS
.
2
MCP11X
V
DD
V
DD
V
DD
V
OUT
MCLR
(Reset Input)
GND
V
SS
PICmicro
Microcontroller
3
1
R
PU
(1)
Note 1:
R
PU
may be required with the MCP111
due to the open-drain output. Resistor
R
PU
is not required with the MCP112.
0.1
μF
V
DD
V
TRIPMAX
V
TRIPMIN
V
TRIPAC
V
TRIPAC
V
TRIPAC
+ V
HYSAC
V
OUT
1V
< 1 V is outside the
device specifications
相關PDF資料 |
PDF描述 |
|---|---|
| MCP1252(中文) | Low Noise, Positive-Regulated Charge Pump(低噪聲、正向調節電荷泵) |
| MCP1253(中文) | Low Noise, Positive-Regulated Charge Pump(低噪聲、正向調節電荷泵) |
| MCP1256 | Regulated 3.3V, Low-Ripple Charge Pump with Low- Operating Current SLEEP Mode or BYPASS Mode |
| MCP1256-EMF | Regulated 3.3V, Low-Ripple Charge Pump with Low- Operating Current SLEEP Mode or BYPASS Mode |
| MCP1256-EUN | Regulated 3.3V, Low-Ripple Charge Pump with Low- Operating Current SLEEP Mode or BYPASS Mode |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP131-195E/LB | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Micropower Voltage Supervisors |
| MCP131-195E/TO | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Micropower Voltage Supervisors |
| MCP131-195E/TT | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Micropower Voltage Supervisors |
| MCP131-195I/LB | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Micropower Voltage Supervisors |
| MCP131-195I/TO | 功能描述:監控電路 Open Drain Low RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。