- 您現在的位置：買賣IC網 > PDF目錄383585 > MCP1319T (Microchip Technology Inc.) Voltage Supervisor PDF資料下載
參數資料
| 型號： | MCP1319T |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | Voltage Supervisor |
| 中文描述： | 電壓監控 |
| 文件頁數： | 22/44頁 |
| 文件大?。?/td> | 924K |
| 代理商： | MCP1319T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
MCP131X/2X
DS21985A-page 22
2005 Microchip Technology Inc.
3.1
Ground Terminal (V
SS
)
V
SS
provides the negative reference for the analog
input voltage. Typically, the circuit ground is used.
3.2
Supply Voltage (V
DD
)
V
DD
can be used for power supply monitoring or a
voltage level that requires monitoring.
3.3
Reset Output (RST and RST)
There are four types of Reset output pins. These are:
1.
Open-Drain active-low Reset, External pull-up
resistor required
Open-Drain active-low Reset, Internal pull-up
resistor
Push-Pull active-low Reset
Push-Pull active-high Reset
2.
3.
4.
Some devices have both an active-low and active-high
Reset output.
3.3.1
ACTIVE-LOW (RST) - OPEN-DRAIN,
EXTERNAL PULL-UP RESISTOR
The RST open-drain output remains low while V
DD
is
below the Reset voltage threshold (V
TRIP
). Once the
device voltage (V
DD
) returns to a high level (V
TRIP
+
V
HYS
), the device will remain in Reset for the Reset
delay timer (T
RST
). After that time expires, the RST pin
will float, and an external pull-up resistor is required to
bring the output to the high state.
3.3.2
ACTIVE-LOW (RST) - OPEN-DRAIN,
INTERNAL PULL-UP RESISTOR
The RST open-drain output remains low while V
DD
is
below the Reset voltage threshold (V
TRIP
). Once the
device voltage (V
DD
) returns to a high level (V
TRIP
+
V
HYS
), the device will remain in Reset for the Reset
delay timer (T
RST
). After that time expires, the RST pin
will be pulled high by an internal pull-up resistor (typi-
cally 4.7 k
Ω
).
3.3.3
ACTIVE-LOW (RST) - PUSH-PULL
The RST push-pull output remains low while V
DD
is
below the Reset voltage threshold (V
TRIP
). Once the
device voltage (V
DD
) returns to a high level (V
TRIP
+
V
HYS
), the device will remain in Reset for the Reset
delay timer (T
RST
). After that time expires, the RST pin
will be driven to the high state.
3.3.4
ACTIVE-HIGH (RST) - PUSH-PULL
The RST push-pull output remains high while V
DD
is
below the Reset voltage threshold (V
TRIP
). Once the
device voltage (V
DD
) returns to a high level (V
TRIP
+
V
HYS
), the device will remain in Reset for the Reset
delay timer (T
RST
). After that time expires, the RST pin
will be driven to the low state.
3.4
Manual Reset Input (MR)
The Manual Reset (MR) input pin allows a push button
switch to easily be connected to the system. When the
push button is depressed, it forces a system Reset.
This pin has circuitry that filters noise that may be
present on the MR signal.
The MR pin is active-low and has an internal pull-up
resistor.
3.5
Watchdog Input
In some systems, it is desirable to have an external
Watchdog Timer to monitor the operation of the sys-
tem. This is done by requiring the embedded controller
to “pet” the Watchdog Timer within a predetermined
time frame (T
WD
). If the MCP131X/2X is not “petted”
within this time frame, the MCP131X/2X will force the
Reset pin(s) active.
The embedded controller “pets” the MCP131X/2X by
forcing an edge transition on the WDI pin. The WDT
Timer is activated by the first falling edge on the WDI
pin.
The standard offering devices have a typical Watchdog
Timer period (T
WD
) of 1.6 s. Table 1-3 shows the avail-
able Watchdog Timer periods.
相關PDF資料 |
PDF描述 |
|---|---|
| MCP131X | Voltage Supervisor |
| MCP1320 | Voltage Supervisor |
| MCP1320T | Voltage Supervisor |
| MCP1321 | Voltage Supervisor |
| MCP1321T | Voltage Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP1319T-29LE/OT | 功能描述:監控電路 Act low P-P Act high P-P RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MCP1319T-46LE/OT | 功能描述:監控電路 Act low P-P Act high P-P RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MCP131T-195E/LB | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Micropower Voltage Supervisors |
| MCP131T-195E/TO | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Micropower Voltage Supervisors |
| MCP131T-195E/TT | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Micropower Voltage Supervisors |
發布緊急采購，3分鐘左右您將得到回復。