- 您現在的位置：買賣IC網 > PDF目錄383585 > MCP1317T (Microchip Technology Inc.) Voltage Supervisor PDF資料下載
參數資料
| 型號： | MCP1317T |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | Voltage Supervisor |
| 中文描述： | 電壓監控 |
| 文件頁數： | 33/44頁 |
| 文件大?。?/td> | 924K |
| 代理商： | MCP1317T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
2005 Microchip Technology Inc.
DS21985A-page 33
MCP131X/2X
5.7
Controllers and Processors With
Bidirectional I/O Pins
Some microcontrollers have bidirectional Reset pins.
Depending on the current drive capability of the control-
ler pin, an indeterminate logic level may result if there
is a logic conflict. This can be avoided by adding a
4.7 k
Ω
resistor in series with the output of the
MCP131X/2X (Figure 5-7). If there are other compo-
nents in the system that require a Reset signal, they
should be buffered so as not to load the Reset line. If
the other components are required to follow the Reset
I/O of the microcontroller, the buffer should be con-
nected as shown with the solid line.
FIGURE 5-7:
MCP131X/2X Push-Pull outputs to a
Bidirectional Reset I/O.
Interfacing the
5.8
RESET Signal Integrity During
Power-Down
The MCP131X/2X Reset output is valid to V
DD
= 1.0V.
Below this 1.0V, the output becomes an "open circuit"
and does not sink or source current. This means
CMOS logic inputs to the microcontroller will be floating
at an undetermined voltage. Most digital systems are
completely shut down well above this voltage.
However, in situations where the Reset signal must be
maintained valid to V
DD
= 0V, external circuitry is
required.
For devices where the Reset signal is active-low, a
pull-down resistor must be connected from the
MCP131X/2X Reset pin(s) to ground to discharge stray
capacitances and hold the output low (Figure 5-8).
Similarly for devices where the Reset signal is
active-high, a pull-up resistor to V
DD
is required to
ensure a valid high Reset signal for V
DD
below 1.0V.
This resistor value, though not critical, should be
chosen such that it does not appreciably load the Reset
pin(s) under normal operation (100 k
Ω
will be suitable
for most applications).
FIGURE 5-8:
Reset pin output state as
V
DD
approaches 0V.
Ensuring a valid active-low
MCP13XX
V
DD
RST
GND
MCLR
GND
Buffered Reset
To Other System
Components
MCU
4.7 k
Ω
Buffer
PICmicro
MCP13XX
V
DD
V
DD
R
1
100 k
Ω
RST
GND
相關PDF資料 |
PDF描述 |
|---|---|
| MCP1401 | Tiny 500 mA, High-Speed Power MOSFET Driver |
| MCP1402 | Tiny 500 mA, High-Speed Power MOSFET Driver |
| MCP1405 | 4.5A Dual High-Speed Power MOSFET Drivers |
| MCP1403 | 4.5A Dual High-Speed Power MOSFET Drivers |
| MCP1404 | 4.5A Dual High-Speed Power MOSFET Drivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP1317T-29LE/OT | 功能描述:監控電路 Active high P-P RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MCP1317T-46LE/OT | 功能描述:監控電路 Active high P-P RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MCP1318 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Voltage Supervisor |
| MCP1318M | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Voltage Supervisor |
| MCP1318MT | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Voltage Supervisor |
發布緊急采購，3分鐘左右您將得到回復。