參數資料
型號： MCF51AG128VLK
元件分類： 微控制器/微處理器
英文描述： MICROCONTROLLER, PQFP80
封裝： 12 X 12 MM, 1.70 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-80
文件頁數： 41/84頁
文件大?。?/td> 3949K
代理商： MCF51AG128VLK
MB95410H/470H Series
46
DS702-00004-1v0-E
(Continued)
*3: Applicable to the following pins: P00 to P07, P10, P11, P13 to P16, P20 to P22, P40 to P43, P50 to P53,
P60 to P67, P90 to P94, PA0 to PA7, PB0 to PB4, PC0 to PC7, PE0 to PE7, PF0, PF1, PG1 and PG2 (P40
to P43, P50 to P53, P94, PB2 to PB4 and PC4 to PC7 are only available on the MB95410H Series.)
Use under recommended operating conditions.
Use with DC voltage (current).
The HV (High Voltage) signal is an input signal exceeding the VCC voltage. Always connect a limiting resistor
between the HV (High Voltage) signal and the microcontroller before applying the HV (High Voltage) signal.
The value of the limiting resistance should be set so that when the HV (High Voltage) signal is applied the
input current to the microcontroller pin does not exceed rated values, either instantaneously or for prolonged
periods.
When the microcontroller drive current is low, such as in low power consumption modes, the HV (High
Voltage) input potential may pass through the protective diode to increase the potential of the VCC pin, and
thus affects other devices.
If the HV (High Voltage) signal is input when the microcontroller power supply is off (not fixed at 0 V), since
power is supplied from the pins, incomplete operations may be executed.
If the HV (High Voltage) input is input after power-on, since power is supplied from the pins, the voltage
of power supply may not be sufficient to enable a power-on reset.
Do not leave the HV (High Voltage) input pin unconnected.
Example of a recommended circuit
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
HV(High Voltage) input (0 V to 16 V)
Protective diode
VCC
N-ch
P-ch
R
Limiting
resistor
Input/Output equivalent circuit
相關PDF資料
PDF描述
MCF51AG96VLF MICROCONTROLLER, PQFP64
MCF51JE128VMB 32-BIT, FLASH, 50.33 MHz, MICROCONTROLLER, PBGA81
MCF51JE256VLL 32-BIT, FLASH, 50.33 MHz, MICROCONTROLLER, PQFP100
MCF51JE256VMB 32-BIT, FLASH, 50.33 MHz, MICROCONTROLLER, PBGA81
MCF51JE256CLK 32-BIT, FLASH, 50.33 MHz, MICROCONTROLLER, PQFP80
相關代理商/技術參數
參數描述
MCF51AG128VQH 功能描述:32位微控制器 - MCU ColdFire V1 128K FL RoHS:否 制造商:Texas Instruments 核心:C28x 處理器系列:TMS320F28x 數據總線寬度:32 bit 最大時鐘頻率:90 MHz 程序存儲器大小:64 KB 數據 RAM 大小:26 KB 片上 ADC:Yes 工作電源電壓:2.97 V to 3.63 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:LQFP-80 安裝風格:SMD/SMT
MCF51AG96 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:MCF51AG128 ColdFire Microcontroller
MCF51AG96CLF 功能描述:32位微控制器 - MCU ColdFire V1 96K FL RoHS:否 制造商:Texas Instruments 核心:C28x 處理器系列:TMS320F28x 數據總線寬度:32 bit 最大時鐘頻率:90 MHz 程序存儲器大小:64 KB 數據 RAM 大小:26 KB 片上 ADC:Yes 工作電源電壓:2.97 V to 3.63 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:LQFP-80 安裝風格:SMD/SMT
MCF51AG96CLH 功能描述:32位微控制器 - MCU ColdFire V1 96K FL RoHS:否 制造商:Texas Instruments 核心:C28x 處理器系列:TMS320F28x 數據總線寬度:32 bit 最大時鐘頻率:90 MHz 程序存儲器大小:64 KB 數據 RAM 大小:26 KB 片上 ADC:Yes 工作電源電壓:2.97 V to 3.63 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:LQFP-80 安裝風格:SMD/SMT
MCF51AG96CLK 功能描述:32位微控制器 - MCU ColdFire V1 96K FL RoHS:否 制造商:Texas Instruments 核心:C28x 處理器系列:TMS320F28x 數據總線寬度:32 bit 最大時鐘頻率:90 MHz 程序存儲器大小:64 KB 數據 RAM 大小:26 KB 片上 ADC:Yes 工作電源電壓:2.97 V to 3.63 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:LQFP-80 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*