參數資料
型號： MC9S12E128CFU
廠商： Freescale Semiconductor
文件頁數： 394/606頁
文件大?。?/td> 0K
描述： IC MCU 128K FLASH 25MHZ 80-QFP
標準包裝： 84
系列： HCS12
核心處理器： HCS12
芯體尺寸： 16-位
速度： 25MHz
連通性： EBI/EMI，I²C，SCI，SPI
外圍設備： POR，PWM，WDT
輸入/輸出數： 60
程序存儲器容量： 128KB（128K x 8）
程序存儲器類型： 閃存
RAM 容量： 8K x 8
電壓 - 電源 (Vcc/Vdd)： 2.35 V ~ 2.75 V
數據轉換器： A/D 16x10b; D/A 2x8b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 80-QFP
包裝： 托盤
配用： M68EVB912E128-ND - BOARD EVAL FOR MC9S12E128/64
Chapter 15 Background Debug Module (BDMV4)
MC9S12E128 Data Sheet, Rev. 1.07
Freescale Semiconductor
453
5
ENTAG
Tagging Enable — This bit indicates whether instruction tagging in enabled or disabled. It is set when the
TAGGO command is executed and cleared when BDM is entered. The serial system is disabled and the tag
function enabled 16 cycles after this bit is written. BDM cannot process serial commands while tagging is active.
0 Tagging not enabled or BDM active
1 Tagging enabled
4
SDV
Shift Data Valid — This bit is set and cleared by the BDM hardware. It is set after data has been transmitted as
part of a rmware read command or after data has been received as part of a rmware write command. It is
cleared when the next BDM command has been received or BDM is exited. SDV is used by the standard BDM
rmware to control program ow execution.
0 Data phase of command not complete
1 Data phase of command is complete
3
TRACE
TRACE1 BDM Firmware Command is Being Executed — This bit gets set when a BDM TRACE1 rmware
command is rst recognized. It will stay set as long as continuous back-to-back TRACE1 commands are
executed. This bit will get cleared when the next command that is not a TRACE1 command is recognized.
0 TRACE1 command is not being executed
1 TRACE1 command is being executed
2
CLKSW
Clock Switch — The CLKSW bit controls which clock the BDM operates with. It is only writable from a hardware
BDM command. A 150 cycle delay at the clock speed that is active during the data portion of the command will
occur before the new clock source is guaranteed to be active. The start of the next BDM command uses the new
clock for timing subsequent BDM communications.
Table 15-3 shows the resulting BDM clock source based on the CLKSW and the PLLSEL (Pll select from the
clock and reset generator) bits.
Note: The BDM alternate clock source can only be selected when CLKSW = 0 and PLLSEL = 1. The BDM serial
interface is now fully synchronized to the alternate clock source, when enabled. This eliminates frequency
restriction on the alternate clock which was required on previous versions. Refer to the device overview
section to determine which clock connects to the alternate clock source input.
Note: If the acknowledge function is turned on, changing the CLKSW bit will cause the ACK to be at the new rate
for the write command which changes it.
1
UNSEC
Unsecure — This bit is only writable in special single-chip mode from the BDM secure rmware and always gets
reset to zero. It is in a zero state as secure mode is entered so that the secure BDM rmware lookup table is
enabled and put into the memory map along with the standard BDM rmware lookup table.
The secure BDM rmware lookup table veries that the on-chip EEPROM and FLASH EEPROM are erased. This
being the case, the UNSEC bit is set and the BDM program jumps to the start of the standard BDM rmware
lookup table and the secure BDM rmware lookup table is turned off. If the erase test fails, the UNSEC bit will
not be asserted.
0 System is in a secured mode
1 System is in a unsecured mode
Note: When UNSEC is set, security is off and the user can change the state of the secure bits in the on-chip
FLASH EEPROM. Note that if the user does not change the state of the bits to “unsecured” mode, the
system will be secured again when it is next taken out of reset.
Table 15-3. BDM Clock Sources
PLLSEL
CLKSW
BDMCLK
0
Bus clock
0
1
Bus clock
Table 15-2. BDMSTS Field Descriptions (continued)
Field
Description
相關PDF資料
PDF描述
1828855-2 CONN 625/125 LIGHTCRIMP+ YELLOW
1828855-1 CONN 625/125 LIGHTCRIMP+ RED
1828854-4 CONN KIT XG LIGHTCRIMP+ BLUE
1828854-3 CONN KIT XG LIGHTCRIMP+ GRN
M20G222J1 CAP CER 2200PF 100V 5% RADIAL
相關代理商/技術參數
參數描述
MC9S12E128CFUE 功能描述:16位微控制器 - MCU 16 Bit 16MHz RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
MC9S12E128CPV 功能描述:16位微控制器 - MCU 16 Bit 16MHz RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
MC9S12E128CPVE 功能描述:16位微控制器 - MCU 16 Bit 16MHz RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
MC9S12E128MFU 功能描述:IC MCU 128K FLASH 25MHZ 80-QFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HCS12 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
MC9S12E128MFUE 功能描述:16位微控制器 - MCU MORAY EEL RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*