參數資料
型號： MC7457RX867NC
廠商： Freescale Semiconductor
文件頁數： 53/71頁
文件大?。?/td> 0K
描述： IC MPU RISC 32BIT 483FCCBGA
標準包裝： 36
系列： MPC74xx
處理器類型： 32-位 MPC74xx PowerPC
速度： 867MHz
電壓： 1.1V
安裝類型： 表面貼裝
封裝/外殼： 483-BCBGA，F(xiàn)CCBGA
供應商設備封裝： 483-FCCBGA（29x29）
包裝： 托盤
System Design Information
MPC7457 RISC Microprocessor Hardware Specifications, Rev. 8
Freescale Semiconductor
57
If address or data parity is not used by the system, and the respective parity checking is disabled through
HID0, the input receivers for those pins are disabled, and those pins do not require pull-up resistors and
should be left unconnected by the system. If all parity generation is disabled through HID0, all parity
checking should also be disabled through HID0, and all parity pins may be left unconnected by the system.
The L3 interface does not normally require pull-up resistors. Unused L3_ADDR signals are driven low
when the SRAM is configured to be less than 1 M in size via L3CR. For example, L3_ADD[18] will be
driven low if the SRAM size is configured to be 2 M; likewise, L3_ADDR[18:17] will be driven low if
the SRAM size is configured to be 1 M.
9.7
JTAG Configuration Signals
Boundary-scan testing is enabled through the JTAG interface signals. The TRST signal is optional in the
IEEE 1149.1 specification, but is provided on all processors that implement the PowerPC architecture.
While it is possible to force the TAP controller to the reset state using only the TCK and TMS signals, more
reliable power-on reset performance will be obtained if the TRST signal is asserted during power-on reset.
Because the JTAG interface is also used for accessing the common on-chip processor (COP) function,
simply tying TRST to HRESET is not practical.
The COP function of these processors allows a remote computer system (typically, a PC with dedicated
hardware and debugging software) to access and control the internal operations of the processor. The COP
interface connects primarily through the JTAG port of the processor, with some additional status
monitoring signals. The COP port requires the ability to independently assert HRESET or TRST in order
to fully control the processor. If the target system has independent reset sources, such as voltage monitors,
watchdog timers, power supply failures, or push-button switches, the COP reset signals must be merged
into these signals with logic.
The arrangement shown in Figure 26 allows the COP port to independently assert HRESET or TRST,
while ensuring that the target can drive HRESET as well. If the JTAG interface and COP header will not
be used, TRST should be tied to HRESET through a 0-Ω isolation resistor so that it is asserted when the
system reset signal (HRESET) is asserted, ensuring that the JTAG scan chain is initialized during
power-on. While Freescale recommends that the COP header be designed into the system as shown in
Figure 26, if this is not possible, the isolation resistor will allow future access to TRST in the case where
a JTAG interface may need to be wired onto the system in debug situations.
The COP header shown in Figure 26 adds many benefits—breakpoints, watchpoints, register and memory
examination/modification, and other standard debugger features are possible through this interface—and
can be as inexpensive as an unpopulated footprint for a header to be added when needed.
The COP interface has a standard header for connection to the target system, based on the 0.025"
square-post, 0.100" centered header assembly (often called a Berg header). The connector typically has
pin 14 removed as a connector key.
There is no standardized way to number the COP header shown in Figure 26; consequently, many different
pin numbers have been observed from emulator vendors. Some are numbered top-to-bottom then
left-to-right, while others use left-to-right then top-to-bottom, while still others number the pins counter
clockwise from pin 1 (as with an IC). Regardless of the numbering, the signal placement recommended in
Figure 26 is common to all known emulators.
相關PDF資料
PDF描述
FMC36DRAS CONN EDGECARD 72POS R/A .100 SLD
MC68EC040RC40A IC MPU 32BIT 40MHZ 179-PGA
MPC8560VTAQFC MPU POWERQUICC III 783FCPBGA
MPC8548EVTATGB MPU POWERQUICC III 783-PBGA
MPC8548EPXATGB MPU POWERQUICC III 783-PBGA
相關代理商/技術參數
參數描述
MC7457TRX1000LC 制造商:Freescale Semiconductor 功能描述:MPC74XX RISC 32-BIT 0.13UM 1GHZ 1.5V/1.8V/2.5V 483-PIN FCCBG - Trays
MC7457TRX1000NC 功能描述:微處理器 - MPU APOLO7 RV1.2 1.1V -40C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MC7457TRX1267LC 制造商:Freescale Semiconductor 功能描述:MPC74XX RISC 32-BIT 0.13UM 1.267GHZ 1.5V/1.8V/2.5V 483-PIN F - Trays
MC7457VG1000LC 功能描述:微處理器 - MPU APOLO7 RV1.2 1.3V 105C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MC7457VG1000NC 功能描述:微處理器 - MPU APOLO7 RV1.2 1.1V 105C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*