參數資料
型號： MC705P6ACPE
廠商： Freescale Semiconductor
文件頁數： 55/98頁
文件大小： 0K
描述： IC MCU 2.1MHZ 4.5K OTP 28-DIP
標準包裝： 13
系列： HC05
核心處理器： HC05
芯體尺寸： 8-位
速度： 2.1MHz
連通性： SIO
外圍設備： POR，WDT
輸入/輸出數： 21
程序存儲器容量： 4.5KB（4.5K x 8）
程序存儲器類型： OTP
RAM 容量： 176 x 8
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 5.5 V
數據轉換器： A/D 4x8b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 28-DIP（0.600"，15.24mm）
包裝： 管件
EPROM Bootloader
MC68HC705P6A Advance Information Data Sheet, Rev. 2.1
Freescale Semiconductor
59
10.6 EPROM Bootloader
Three port pins are associated with bootloader control functions: PC3, PC4, and PC6. Table 10-2
summarizes their functionality.
10.7 Programming from an External Memory Device
In this programming mode, PC5 must be connected to VSS. PC4 and PC3 are used to select the
programming mode. The programming circuit shown in Figure 10-2 uses an external 12-bit counter to
address the memory device containing the code to be copied. This counter requires a clock and a reset
function. The 12-bit counter can address up to 4 Kbytes of memory, which means that a port pin has to
be used to address the remaining 4 K of the 8-K memory space.
The following procedure explains how to use the programming circuit shown in Figure 10-2 to copy a user
program from an external memory device into the MCU’s EPROM:
1.
Program a 2764-type EPROM device with the desired instructions and data. Code programmed
into the 2764 must appear at the same addresses desired in the MC68HC705P6A. Therefore, the
page zero code must start at $0020 and end at $004F, the main body of code must start at $0100
and end at $12FF, and the user vectors must start at $1FF0 and end at $1FFF.
NOTE
The MOR data must appear at $1EFF and $1F00.
2.
Install the programmed 2764 device into the programming circuit.
3.
Install the MC68HC705P6A to be programmed into the programming circuit.
4.
Set the PROGRAM and/or VERIFY switches for the desired operation (an open switch is the active
state) and close the RESET switch to hold the MCU in reset.
5.
Make sure that the VPP source is OFF.
6.
Apply the VDD source to the programming circuit.
7.
Apply the VPP source to the programming circuit.
8.
Open the RESET switch to allow the MCU to come out of reset and begin execution of the software
in its internal bootloader ROM.
9.
Wait for programming and/or verification to complete (about 40 seconds). The PROGRAM LED will
light during programming and the VERIFY LED will light if verification was requested and was
successful.
10.
When complete, close the RESET switch to force the MCU into the reset state.
11.
Turn off the VPP source.
12.
Turn off the VDD source.
13.
Remove device(s).
Table 10-2. Bootloader Control Pins
PC6
PC4
PC3
Mode
111
Program/verify
110
Verify only
1
0
Dump MCU EPROM to port A
相關PDF資料
PDF描述
VJ2225Y125KBBAT4X CAP CER 1.2UF 100V 10% X7R 2225
VJ2225Y124JBCAT4X CAP CER 0.12UF 200V 5% X7R 2225
VJ2225Y184JBCAT4X CAP CER 0.18UF 200V 5% X7R 2225
VJ2225Y274JBCAT4X CAP CER 0.27UF 200V 5% X7R 2225
VJ2225Y394JBCAT4X CAP CER 0.39UF 200V 5% X7R 2225
相關代理商/技術參數
參數描述
MC705P6AMDWE 功能描述:8位微控制器 -MCU MCU 176 BYTES RAM EPP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC705P6AMPE 功能描述:8位微控制器 -MCU 705P6A 176 BYTES RAM EPP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC705P6ECDWE 功能描述:8位微控制器 -MCU MC68HC705P6E SERIES RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC705P6ECPE 功能描述:8位微控制器 -MCU 8B OTP MCU - 705P6E RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC705SR3CFBE 功能描述:8位微控制器 -MCU 8B MCU 192 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*