- 您現在的位置：買賣IC網 > PDF目錄45226 > MC68L11D0CFB3 (MOTOROLA INC) 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQFP44 PDF資料下載
參數資料
| 型號： | MC68L11D0CFB3 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQFP44 |
| 封裝： | 10 X 10 MM, 2 MM HEIGHT, 0.80 MM PITCH, QFP-44 |
| 文件頁數： | 41/131頁 |
| 文件大小： | 1640K |
| 代理商： | MC68L11D0CFB3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁
MC68HC11D3
PIN DESCRIPTIONS
MOTOROLA
TECHNICAL DATA
2-5
sensitive, it can be connected to a multiple-source wired-OR network with an external
pullup resistor to VDD. XIRQ is often used as a power loss detect interrupt.
Whenever XIRQ or IRQ are used with multiple interrupt sources (IRQ must be config-
ured for level-sensitive operation if there is more than one source of IRQ interrupt),
each source must drive the interrupt input with an open-drain type of driver to avoid
contention between outputs. There should be a single pullup resistor near the MCU
interrupt input pin (typically 4.7 k
). There must also be an interlock mechanism at
each interrupt source so that the source holds the interrupt line low until the MCU rec-
ognizes and acknowledges the interrupt request. If one or more interrupt sources are
still pending after the MCU services a request, the interrupt line will still be held low
and the MCU will be interrupted again as soon as the interrupt mask bit in the MCU is
cleared (normally upon return from an interrupt). Refer to SECTION 5 RESETS AND
2.7 MODA and MODB (MODA/LIR,and MODB/VSTBY)
During reset, MODA and MODB select one of the four operating modes. Refer to SEC-
After the operating mode has been selected, the LIR pin provides an open-drain output
to indicate that execution of an instruction has begun. A series of E-clock cycles occurs
during execution of each instruction. The LIR signal goes low during the first E-clock
cycle of each instruction (opcode fetch). This output is provided for assistance in pro-
gram debugging.
The VSTBY pin is used to input RAM standby power. When the voltage on this pin is
more than one MOS threshold (about 0.7 volts) above the VDD voltage, the internal
192-byte RAM and part of the reset logic are powered from this signal rather than the
VDD input. This allows RAM contents to be retained without VDD power applied to the
MCU. Reset must be driven low before VDD is removed and must remain low until VDD
has been restored to a valid level.
2.8 PD6/AS
This pin performs either of two separate functions, depending on the operating mode.
In single-chip and bootstrap modes, the pin functions as input/output port D bit 6. In
the expanded multiplexed and test modes, it provides an address strobe (AS) function.
The AS can demultiplex the address and data signals at port C. Refer to SECTION 4
OPERATING MODES AND ON-CHIP MEMORY for further information.
2.9 PD7/R/W
This pin provides two separate functions, depending on the operating mode. In single-
chip and bootstrap modes, PD7/R/W acts as input/output port D bit 7. Refer to SEC-
TION 6 PARALLEL I/O for further information.
In expanded multiplexed and test modes, PD7/R/W performs a read/write function.
PD7/R/W controls the direction of transfers on the external data bus. A high on this pin
indicates that a read cycle is in progress.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC11D0CFN2R2 | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQCC44 |
| MC68HC11D3CP1 | 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PDIP40 |
| MC68L11D0CFBE2R | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP44 |
| MC68HC711D3CFB | 8-BIT, 2 MHz, MICROCONTROLLER, PQFP44 |
| MC68HC11D3CFB | 8-BIT, 2 MHz, MICROCONTROLLER, PQFP44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68L11D0CFBE2 | 功能描述:8位微控制器 -MCU LO VOLT 8B MCU 192RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC68L11D0CFBE2R | 功能描述:IC MCU 8BIT 192RAM 44-QFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 標準包裝:1 系列:87C 核心處理器:MCS 51 芯體尺寸:8-位 速度:16MHz 連通性:SIO 外圍設備:- 輸入/輸出數:32 程序存儲器容量:8KB（8K x 8） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4 V ~ 6 V 數據轉換器:- 振蕩器型:外部 工作溫度:0°C ~ 70°C 封裝/外殼:44-DIP 包裝:管件 其它名稱:864285 |
| MC68L11D0FNE2 | 功能描述:8位微控制器 -MCU 8B MCU 192RAM LVDC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC68L11E0FN2 | 制造商:Rochester Electronics LLC 功能描述:8-BIT MCU,512RAM,A/D,LVDC - Bulk |
| MC68L11E0FNE2 | 功能描述:IC MCU 8BIT LV 512RAM 52-PLCC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 標準包裝:1 系列:87C 核心處理器:MCS 51 芯體尺寸:8-位 速度:16MHz 連通性:SIO 外圍設備:- 輸入/輸出數:32 程序存儲器容量:8KB（8K x 8） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4 V ~ 6 V 數據轉換器:- 振蕩器型:外部 工作溫度:0°C ~ 70°C 封裝/外殼:44-DIP 包裝:管件 其它名稱:864285 |
發布緊急采購，3分鐘左右您將得到回復。