參數資料
型號： MC68HC705P6ADW
廠商： FREESCALE SEMICONDUCTOR INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDSO28
封裝： SOIC-28
文件頁數： 55/98頁
文件大小： 532K
代理商： MC68HC705P6ADW
EPROM Bootloader
MC68HC705P6A Advance Information Data Sheet, Rev. 2.1
Freescale Semiconductor
59
10.6 EPROM Bootloader
Three port pins are associated with bootloader control functions: PC3, PC4, and PC6. Table 10-2
summarizes their functionality.
10.7 Programming from an External Memory Device
In this programming mode, PC5 must be connected to VSS. PC4 and PC3 are used to select the
programming mode. The programming circuit shown in Figure 10-2 uses an external 12-bit counter to
address the memory device containing the code to be copied. This counter requires a clock and a reset
function. The 12-bit counter can address up to 4 Kbytes of memory, which means that a port pin has to
be used to address the remaining 4 K of the 8-K memory space.
The following procedure explains how to use the programming circuit shown in Figure 10-2 to copy a user
program from an external memory device into the MCU’s EPROM:
1.
Program a 2764-type EPROM device with the desired instructions and data. Code programmed
into the 2764 must appear at the same addresses desired in the MC68HC705P6A. Therefore, the
page zero code must start at $0020 and end at $004F, the main body of code must start at $0100
and end at $12FF, and the user vectors must start at $1FF0 and end at $1FFF.
NOTE
The MOR data must appear at $1EFF and $1F00.
2.
Install the programmed 2764 device into the programming circuit.
3.
Install the MC68HC705P6A to be programmed into the programming circuit.
4.
Set the PROGRAM and/or VERIFY switches for the desired operation (an open switch is the active
state) and close the RESET switch to hold the MCU in reset.
5.
Make sure that the VPP source is OFF.
6.
Apply the VDD source to the programming circuit.
7.
Apply the VPP source to the programming circuit.
8.
Open the RESET switch to allow the MCU to come out of reset and begin execution of the software
in its internal bootloader ROM.
9.
Wait for programming and/or verification to complete (about 40 seconds). The PROGRAM LED will
light during programming and the VERIFY LED will light if verification was requested and was
successful.
10.
When complete, close the RESET switch to force the MCU into the reset state.
11.
Turn off the VPP source.
12.
Turn off the VDD source.
13.
Remove device(s).
Table 10-2. Bootloader Control Pins
PC6
PC4
PC3
Mode
111
Program/verify
110
Verify only
1
0
Dump MCU EPROM to port A
相關PDF資料
PDF描述
MC68HC705P6AMDW 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDSO28
MC68HC705P6AMDWER2 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDSO28
MC68HC705P6ASD 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER
MC68HC705P6AMDWR2 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDSO28
MC68HC705P6ASD 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER
相關代理商/技術參數
參數描述
MC68HC705P6AMDW 功能描述:IC MCU 4.6K OTP 2.1MHZ 28-SOIC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC05 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
MC68HC705P6AMP 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HC705P6CDW 制造商:Motorola Inc 功能描述:
MC68HC705P6CP 制造商:Freescale Semiconductor 功能描述: 制造商:Motorola Inc 功能描述:
MC68HC705P6ECDW 制造商:Motorola Inc 功能描述: 制造商:MOTOROLA 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*