參數資料
型號: MC68HC11K0VFU3
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT MICROCONTROLLER
中文描述: 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQFP80
封裝: QFP-80
文件頁數: 24/80頁
文件大?。?/td> 420K
代理商: MC68HC11K0VFU3
MOTOROLA
24
M68HC11 K Series
MC6HC11KTS/D
LVPEN —Low Voltage Programming Protect Enable
If LVPEN = 1, programming of the EEPROM is enabled unless the LVPI circuit detects that V
DD
has
fallen below a safe operating voltage, thus setting the low voltage programming inhibit bit in PPROG
register (LVPI = 1).
0 = Low voltage programming protect for EEPROM disabled
1 = Low voltage programming protect for EEPROM enabled
BPRT4 —Block Protect Bit for Upper 128 Bytes of EEPROM
Refer to description for BPRT[3:0].
PTCON —Protect for CONFIG
0 = CONFIG register can be programmed or erased normally
1 = CONFIG register cannot be programmed or erased
BPRT[3:0] —Block Protect Bits for EEPROM
0 = Protection disabled
1 = Protection enabled
INIT2 can be written only once in normal modes, any time in special modes.
EE[3:0] —EEPROM Map Position
EEPROM is at $xD80–$xFFF, where x is the hexadecimal digit represented by EE[3:0].
Bits [3:0] —Not implemented
Always read zero
3.5 Configuration Control Register (CONFIG)
The CONFIG register is used to define several system functions. Although the CONFIG register is an
address within the register block, it is actually an EEPROM byte with the address of $x03F. CONFIG is
made up of EEPROM cells and static latches. The operation of the MCU is controlled directly by these
latches and not the actual EEPROM byte. When programming the CONFIG register, the EEPROM byte
is being accessed. When the CONFIG register is being read, the static latches are being accessed.
The CONFIG register can be read at any time. The value read is the one latched from the EEPROM
cells during the last reset sequence. A new value programmed into this register cannot be read until a
subsequent reset occurs. Unused bits always read as ones.
In normal modes (SMOD = 0), CONFIG bits can only be written using the EEPROM programming se-
quence, and are neither readable nor active until latched via the next reset. In special modes (SMOD =
1), CONFIG bits can be written at any time.
Bit Name
BPRT4
BPRT3
BPRT2
BPRT1
BPRT0
Block Protected
$xF80–$xFFF
$xE60–$xF7F
$xDE0–$xE5F
$xDA0–$xDDF
$xD80–$xD9F
Block Size
128 Bytes
288 Bytes
128 Bytes
64 Bytes
32 Bytes
INIT2
—EEPROM Mapping
$0037
Bit 7
6
5
4
3
2
1
Bit 0
EE3
EE2
EE1
EE0
0
0
0
0
RESET:
0
0
0
0
0
0
0
0
相關PDF資料
PDF描述
MC68HC11K0VFU4 8-BIT MICROCONTROLLER
MC68L11K0FN1 8-BIT MICROCONTROLLER
MC68L11K0FN3 8-BIT MICROCONTROLLER
MC68L11K0FU1 8-BIT MICROCONTROLLER
MC68L11K0FU3 8-BIT MICROCONTROLLER
相關代理商/技術參數
參數描述
MC68HC11K0VFU4 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-Bit Microcontroller
MC68HC11K1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontroller Unit
MC68HC11K1CFN2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-Bit Microcontroller
MC68HC11K1CFN3 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNIT
MC68HC11K1CFN4 功能描述:IC MCU 640 EEPROM 4MHZ 84-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:HC11 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C,IrDA,LIN,SPI,UART/USART 外圍設備:DMA,PDR,POR,PVD,PWM,溫度傳感器,WDT 輸入/輸出數:26 程序存儲器容量:64KB(64K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN,36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND