參數資料
型號： MC68C912B32FU8
廠商： MOTOROLA INC
元件分類： 微控制器/微處理器
英文描述： 16-Bit Microcontroller
中文描述： 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP80
封裝： QFP-80
文件頁數： 39/128頁
文件大?。?/td> 748K
代理商： MC68C912B32FU8
MC68HC912B32
MC68HC912B32TS/D
MOTOROLA
39
STRE — Spare Test Row Enable
The spare test row consists of one Flash EEPROM array row. The reserved word at location 31 contains
production test information which must be maintained through several erase cycles. When STRE is set,
the decoding for the spare test row overrides the address lines which normally select the other rows in
the array.
0 = LIB accesses are to the Flash EEPROM array
1 = Spare test row in array enabled if SMOD is active
MWPR — Multiple Word Programming
Used primarily for testing, if MPWR = 1, the two least-significant address lines ADDR[1:0] will be ignored
when programming a Flash EEPROM location. The word location addressed if ADDR[1:0] = 00, along
with the word location addressed if ADDR[1:0] = 10, will both be programmed with the same word data
from the programming latches. This bit should not be changed during programming.
0 = Multiple word programming disabled
1 = Program 32 bits of data
This register controls the programming and erasure of the Flash EEPROM.
FEESWAI — Flash EEPROM Stop in Wait Control
0 = Do not halt Flash EEPROM clock when the part is in wait mode.
1 = Halt Flash EEPROM clock when the part is in wait mode.
NOTE
The FEESWAI bit cannot be asserted if the interrupt vector resides in theFlash
EEPROM array.
SVFP — Status V
FP
Voltage
SVFP is a read only bit.
0 = Voltage of V
FP
pin is below normal programming voltage levels
1 = Voltage of V
FP
pin is above normal programming voltage levels
ERAS — Erase Control
This bit can be read anytime or written when ENPE = 0. When set, all locations in the array will be
erased at the same time. The boot block will be erased only if BOOTP = 0. This bit also affects the result
of attempted array reads. See
Table 14
for more information. Status of ERAS cannot change if ENPE
is set.
0 = Flash EEPROM configured for programming
1 = Flash EEPROM configured for erasure
LAT — Latch Control
This bit can be read anytime or written when ENPE = 0. When set, the Flash EEPROM is configured
for programming or erasure and, upon the next valid write to the array, the address and data will be
latched for the programming sequence. See
Table 14
for the effects of LAT on array reads. A high volt-
age detect circuit on the V
FP
pin will prevent assertion of the LAT bit when the programming voltage is
at normal levels.
0 = Programming latches disabled
1 = Programming latches enabled
FEECTL
— Flash EEPROM Control Register
$00F7
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
FEESWAI
SVFP
ERAS
LAT
ENPE
RESET:
0
0
0
0
0
0
0
0
相關PDF資料
PDF描述
MC68B912B32FU8 16-Bit Microcontroller
MC68C912B32CFU8 16-Bit Microcontroller
MC68CK338 Highly Integrated, Low-Power, 32-Bit Microcontroller
MC68EC060 32-Bit Microprocessors.(32位微處理器)
MC68EN360RC25V QUad Integrated Communications Controller Users Manual
相關代理商/技術參數
參數描述
MC68CK16Z1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC16Z Series
MC68CK16Z1CAG16 功能描述:16位微控制器 - MCU 16BIT 1KRAM 32KHZ CRYSTAL RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
MC68CK16Z1CAG16 制造商:Freescale Semiconductor 功能描述:Microcontroller
MC68CK16Z1CFC16 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC16Z Series
MC68CK16Z1CPV16 功能描述:16位微控制器 - MCU 16 Bit 16MHz RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*