參數資料
型號: MC68331CPV16B1
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 32-BIT, 16 MHz, MICROCONTROLLER, PQFP144
封裝: 20 X 20 MM, 1.40 MM HEIGHT, 0.50 MM PITCH, PLASTIC, LQFP-144
文件頁數: 16/90頁
文件大?。?/td> 481K
代理商: MC68331CPV16B1
MC68331
MOTOROLA
MC68331TS/D
23
3.3.2 Clock Synthesizer Operation
A voltage controlled oscillator (VCO) generates the system clock signal. A portion of the clock signal is
fed back to a divider/counter. The divider controls the frequency of one input to a phase comparator.
The other phase comparator input is a reference signal, either from the internal oscillator or from an
external source. The comparator generates a control signal proportional to the difference in phase be-
tween its two inputs. The signal is low-pass filtered and used to correct VCO output frequency.
The synthesizer locks when VCO frequency is identical to reference frequency. Lock time is affected by
the filter time constant and by the amount of difference between the two comparator inputs. Whenever
comparator input changes, the synthesizer must re-lock. Lock status is shown by the SLOCK bit in SYN-
CR.
The MCU does not come out of reset state until the synthesizer locks. Crystal type, characteristic fre-
quency, and layout of external oscillator circuitry affect lock time.
The low-pass filter requires an external low-leakage capacitor, typically 0.1
F, connected between the
XFC and VDDSYN pins.
VDDSYN is used to power the clock circuits. A separate power source increases MCU noise immunity
and can be used to run the clock when the MCU is powered down. Use a quiet power supply as the
VDDSYN source, since PLL stability depends on the VCO, which uses this supply. Place adequate ex-
ternal bypass capacitors as close as possible to the VDDSYN pin to ensure stable operating frequency.
When the clock synthesizer is used, control register SYNCR determines operating frequency and vari-
ous modes of operation. SYNCR can be read only when the processor is operating at the supervisor
privilege level.
The SYNCR X bit controls a divide by two prescaler that is not in the synthesizer feedback loop. Setting
X doubles clock speed without changing VCO speed. There is no VCO relock delay. The SYNCR W bit
controls a 3-bit prescaler in the feedback divider. Setting W increases VCO speed by a factor of four.
The SYNCR Y field determines the count modulus for a modulo 64 down counter, causing it to divide
by a value of Y
+ 1. When either W or Y value changes, there is a VCO relock delay.
Clock frequency is determined by SYNCR bit settings as follows:
FSYSTEM = FREFERENCE [4(Y + 1)(2
2W +X)]
In order for the device to perform correctly, the clock frequency selected by the W, X, and Y bits must
be within the limits specified for the MCU. The VCO frequency is twice the system clock frequency if X
= 1 or four times the system clock frequency if X = 0.
The reset state of SYNCR ($3F00) produces a modulus-64 count.
3.3.3 Clock Control
The clock control circuits determine system clock frequency and clock operation under special circum-
stances, such as following loss of synthesizer reference or during low-power operation. Clock source is
determined by the logic state of the MODCLK pin during reset.
SYNCR —Clock Synthesizer Control Register
$YFFA04
15
14
13
8
7
6
5
4
3
2
1
0
W
X
Y
EDIV
0
SLIMP
SLOCK RSTEN
STSIM
STEXT
RESET:
0
1
0
U
0
相關PDF資料
PDF描述
MC68331CPV20 32-BIT, 20.97 MHz, MICROCONTROLLER, PQFP144
MC68331CFC25 32-BIT, MICROCONTROLLER, PQFP132
MC68331MFC16 32-BIT, 16.78 MHz, MICROCONTROLLER, PQFP132
MC68331CFC16 32-BIT, 16.78 MHz, MICROCONTROLLER, PQFP132
MC68332GCPV16 32-BIT, 16.78 MHz, MICROCONTROLLER, PQFP144
相關代理商/技術參數
參數描述
MC68331CPV20 制造商:Rochester Electronics LLC 功能描述:32BIT MCU,GPT,SIM,QSM - Bulk
MC68331CPV20B1 制造商:Rochester Electronics LLC 功能描述:32BIT MCU,GPT,SIM,QSM - Bulk
MC68331CPV25 制造商:Rochester Electronics LLC 功能描述:32BIT MCU,GPT,SIM,QSM - Bulk
MC68331LPV20 制造商:Motorola Inc 功能描述:
MC68331MEH16 功能描述:32位微控制器 - MCU 32B MCU GPT SIM QSM RoHS:否 制造商:Texas Instruments 核心:C28x 處理器系列:TMS320F28x 數據總線寬度:32 bit 最大時鐘頻率:90 MHz 程序存儲器大小:64 KB 數據 RAM 大小:26 KB 片上 ADC:Yes 工作電源電壓:2.97 V to 3.63 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:LQFP-80 安裝風格:SMD/SMT