參數資料
型號： MC3PHACVDW
廠商： MOTOROLA INC
元件分類： 運動控制電子
英文描述： 3-Phase AC Motor Controller
中文描述： AC MOTOR CONTROLLER, PDSO28
封裝： PLASTIC, SOIC-28
文件頁數： 24/44頁
文件大小： 724K
代理商： MC3PHACVDW
MC3PHAC/D
24
3-Phase AC Motor Controller
MOTOROLA
Standalone Application Example
Figure 12
shows an application example of the MC3PHAC, configured in
standalone mode. Resistor values and jumpers have been selected to provide
the following performance:
1.
2.
Base frequency of 60 Hz and positive PWM polarity (from
Table 3
)
PWM frequency resistor 3.9 k
, which implies 10.582 kHz from
Table 4
). (5v/(3.9k + 6.8k))*3.9k = 1.82 volts
Dead-time resistor = 5.1 k
, which implies 4.5
μ
s (from
Figure 9
)
Fault retry time resistor = 8.2 k
, which implies 32.8 seconds (from
Figure 10
).
Voltage boost resistor = 12 k
, which implies 25.5 percent (from
Figure 11
).
The wiper of the acceleration potentiometer is set at
2.5 V = 64 Hz/second acceleration rate (from the
Acceleration Control
description on
page 14
.) The potentiometer, in this case, could have
been a resistor divider. If a resistor divider is used in place of the
acceleration potentiometer, keep the total resistance of the two resistors
less than 10 k
. Always use 4.7k
in series with the center of the
acceleration voltage divider resistors, connected to the ACCEL (pin 27)
as shown in the application example,
Figure 12
.
Crystal/resonator capacitor values are typical values from the
manufacturer. Refer to the manufacturers data for actual values.
3.
4.
5.
6.
7.
PC Master Software Operation
Introduction to PC Master Host Software
The MC3PHAC is compatible with Motorola’s PC master host software serial
interface protocol. Communication occurs over an on-chip UART, on the
MC3PHAC at 9600 baud to an external master device, which may be a
microcontroller that also has an integrated UART or a personal computer via a
COM port. With PC master software, an external controller can monitor and
control all aspects of the MC3PHAC operation.
When the MC3PHAC is placed in PC master software mode, all control of the
system is provided through the integrated UART, resident on the MC3PHAC.
Inputs such as START, FWD, SPEED, ACCEL, MUX_IN, and
PWMPOL_BASEFREQ have no controlling influence over operation of the
system. Even though the SPEED, START, and FWD inputs are disabled while
the system is in PC master software mode, through PC master software, it is
possible to monitor the state of those inputs.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料
PDF描述
MC3PHACVFA 3-Phase AC Motor Controller
MC3PHACVP 3-Phase AC Motor Controller
MC3S12C128 16-Bit Microcontroller
MC3S12C32 16-Bit Microcontroller
MC3S12C64 16-Bit Microcontroller
相關代理商/技術參數
參數描述
MC3PHACVDWE 功能描述:馬達/運動/點火控制器和驅動器 8BIT MCU 8K FLASH OTP RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MC3PHACVFA 制造商:Freescale Semiconductor 功能描述:MCU 8BIT HC08 CISC 8KB FLASH 5V 32LQFP - Trays 制造商:Rochester Electronics LLC 功能描述:8BIT MCU, 8K FLASH OTP - Bulk
MC3PHACVFAE 功能描述:馬達/運動/點火控制器和驅動器 8B MCU 8K FLASH OTP RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MC3PHACVP 制造商:Freescale Semiconductor 功能描述:MCU 8BIT HC08 CISC 8KB FLASH 5V 28PDIP - Rail/Tube 制造商:Freescale Semiconductor 功能描述:Controller IC
MC3PHACVPE 功能描述:馬達/運動/點火控制器和驅動器 8BIT MCU 8K FLASH OTP RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*