- 您現在的位置：買賣IC網 > PDF目錄385567 > MC3479 (ON SEMICONDUCTOR) Stepper Motor Driver(步進電機驅動器) PDF資料下載
參數資料
| 型號： | MC3479 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | Stepper Motor Driver(步進電機驅動器) |
| 中文描述： | 步進電機驅動器（步進電機驅動器） |
| 文件頁數： | 8/11頁 |
| 文件大?。?/td> | 182K |
| 代理商： | MC3479 |
MC3479
http://onsemi.com
8
Figure 7. Output Sequence
Phase A
Output
(a) Full Step Mode
A
CW/CCW
A
A
A
A
Bias/Set
Clk
Phase A
Output
Phase A
A
(c) Half Step Mode
C
D
L3
L4
F
L1
L2
E
C
L1
L2
L3
L4
B
D
L1
L2
L3
C
D
B
H
G
D
B
C
E
F
(b) Half Step Mode
L4
G
H
B
B
C
D
B
C
B
= Logic 0"
= Logic 1"
= Logic 1"
= High Impedance
= Logic 0"
= Logic 1", OIC = Logic 0"
CW/CCW
F/HS
D
B
C
= High Impedance
= Logic 0"
= Don
′
t Care
F/HS
OIC
CW/CCW
F/HS
OIC
The value of R
B
(between this pin and ground) is then
determined by:
VM
RB
0.7 V
IBS
b) When this pin is opened (raised to V
M
) such that I
BS
is
<5.0 A, the internal logic is set to the Phase A condition, and
the four driver outputs are put into a high impedance state. The
Phase A output (Pin 11) goes active (low), and input signals at
the controls are ignored during this time. Upon re
establishing
I
BS
, the driver outputs become active, and will be in the Phase
A position (L1 = L3 = V
OHD
, L2 = L4 = V
OLD
). The circuit
will then respond to the inputs at the controls.
The Set function (opening this pin) can be used as a
power
up reset while supply voltages are settling. A CMOS
logic gate (powered by V
M
) can be used to control this pin
as shown in Figure 12.
c) Whenever the motor is not being stepped, power
dissipation in the IC and in the motor may be lowered by
reducing I
BS
, so as to reduce the output (motor) current.
Setting I
BS
to 75 A will reduce the motor current, but will
not reset the internal logic as described above. See Figure 13
for a suggested circuit.
Power Dissipation
The power dissipated by the MC3479 must be such that
the junction temperature (T
J
) does not exceed 150
°
C. The
power dissipated can be expressed as:
P = (V
M
I
M
) + (2
I
OD
) [(V
M
V
OHD
) + V
OLD
]
where
V
M
= Supply voltage;
I
M
= Supply current other than I
OD
;
I
OD
= Output current to each motor coil;
V
OHD
= Driver output high voltage;
V
OLD
= Driver output low voltage.
The power supply current (I
M
) is obtained from Figure 8.
After the power dissipation is calculated, the junction
temperature can be calculated using:
T
J
= (P
R
JA
) + T
A
where
R
JA
= Junction
to
ambient thermal resistance
(52
°
C/W for the DIP, 72
°
C/W for the FN Package);
T
A
= Ambient Temperature.
相關PDF資料 |
PDF描述 |
|---|---|
| MC44BC375 | PLL Tuned VHF Audio/ Video High Integration Modulator ICs |
| MC44BC375J | PLL Tuned VHF Audio/ Video High Integration Modulator ICs |
| MC44BC375JD | PLL Tuned VHF Audio/ Video High Integration Modulator ICs |
| MC44BC375T | PLL Tuned VHF Audio/ Video High Integration Modulator ICs |
| MC44BC375TD | PLL Tuned VHF Audio/ Video High Integration Modulator ICs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC34791 | 制造商:SPC Multicomp 功能描述:CONNECTOR FPC 1.25MM 6WAY 制造商:SPC Multicomp 功能描述:CONNECTOR, FPC, 1.25MM, 6WAY |
| MC34793 | 制造商:SPC Multicomp 功能描述:CONNECTOR FPC 1.25MM 8WAY 制造商:SPC Multicomp 功能描述:CONNECTOR, FPC, 1.25MM, 8WAY |
| MC34795 | 制造商:SPC Multicomp 功能描述:CONNECTOR FPC 1.25MM 8WAY 制造商:SPC Multicomp 功能描述:CONNECTOR, FPC, 1.25MM, 8WAY |
| MC34797 | 制造商:SPC Multicomp 功能描述:CONNECTOR FPC 1.25MM 10WAY |
| MC34799 | 制造商:SPC Multicomp 功能描述:CONNECTOR FPC 1.25MM 10WAY 制造商:SPC Multicomp 功能描述:CONNECTOR, FPC, 1.25MM, 10WAY |
發(fā)布緊急采購，3分鐘左右您將得到回復。
