- 您現在的位置：買賣IC網 > PDF目錄385567 > MC34262D (ON SEMICONDUCTOR) POWER FACTOR CONTROLLERS PDF資料下載
參數資料
| 型號： | MC34262D |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 穩壓器 |
| 英文描述： | POWER FACTOR CONTROLLERS |
| 中文描述： | 0.5 A POWER FACTOR CONTROLLER, PDSO8 |
| 封裝： | PLASTIC, SOIC-8 |
| 文件頁數： | 9/16頁 |
| 文件大?。?/td> | 393K |
| 代理商： | MC34262D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
MC34262 MC33262
APPLICATIONS INFORMATION
9
MOTOROLA ANALOG IC DEVICE DATA
The application circuits shown in Figures 19, 20 and 21
reveal that few external components are required for a
complete power factor preconverter. Each circuit is a peak
detecting current–mode boost converter that operates in
critical conduction mode with a fixed on–time and variable
off–time. A major benefit of critical conduction operation is
that the current loop is inherently stable, thus eliminating the
need for ramp compensation. The application in Figure 19
operates over an input voltage range of 90 Vac to 138 Vac
and provides an output power of 80 W (230 V at 350 mA) with
an associated power factor of approximately 0.998 at
nominal line. Figures 20 and 21 are universal input
preconverter examples that operate over a continuous input
voltage range of 90 Vac to 268 Vac. Figure 20 provides an
output power of 175 W (400 V at 440 mA) while Figure 21
provides 450 W (400 V at 1.125 A). Both circuits have an
observed worst–case power factor of approximately 0.989.
The input current and voltage waveforms of Figure 20 are
shown in Figure 22 with operation at 115 Vac and 230 Vac.
The data for each of the applications was generated with the
test set–up shown in Figure 24.
Table 1. Design Equations
Notes
Calculation
Formula
Calculate the maximum required output power.
Required Converter Output Power
PO = VO IO
Calculated at the minimum required ac line voltage
for output regulation. Let the efficiency
η
= 0.92 for
low line operation.
Peak Inductor Current
IL(pk) =
2
2 PO
η
Vac(LL)
Let the switching cycle t = 40
μ
s for universal input
(85 to 265 Vac) operation and 20
μ
s for fixed input
(92 to 138 Vac, or 184 to 276 Vac) operation.
Inductance
LP =
t
2 VO PO
V2
η
Vac(LL)2
In theory the on–time ton is constant. In practice ton
tends to increase at the ac line zero crossings due
to the charge on capacitor C5. Let Vac = Vac(LL) for initial
ton and toff calculations.
The off–time toff is greatest at the peak of the ac line
voltage and approaches zero at the ac line zero
crossings. Theta (
θ
) represents the angle of the ac
line voltage.
Switch On–Time
η
Vac2
ton =
2 PO LP
Switch Off–Time
VO
– 1
toff =
2 Vac
Sin
θ
ton
The minimum switching frequency occurs at the peak
of the ac line voltage. As the ac line voltage traverses
from peak to zero, toff approaches zero producing an
increase in switching frequency.
Switching Frequency
f =
ton + toff
1
Set the current sense threshold VCS to 1.0 V for
universal input (85 Vac to 265 Vac) operation and
to 0.5 V for fixed input (92 Vac to 138 Vac, or
184 Vac to 276 Vac) operation. Note that VCS must
be <1.4 V.
Peak Switch Current
R7 =
IL(pk)
VCS
Set the multiplier input voltage VM to 3.0 V at high
line. Empirically adjust VM for the lowest distortion
over the ac line voltage range while guaranteeing
startup at minimum line.
Multiplier Input Voltage
+ 1
Vac
VM =
R5
R3
2
The IIB R1 error term can be minimized with a divider
current in excess of 50
μ
A.
Converter Output Voltage
– IIB R2
VO = Vref
R2+ 1
R1
The calculated peak–to–peak ripple must be less than
16% of the average dc output voltage to prevent false
tripping of the Overvoltage Comparator. Refer to the
Overvoltage Comparator text. ESR is the equivalent
series resistance of C3
The bandwidth is typically set to 20 Hz. When operating
at high ac line, the value of C1 may need to be
increased. (See Figure 25)
Converter Output
Peak to Peak
Ripple Voltage
2
+ ESR2
2
π
fac C3
VO(pp) = IO
1
Error Amplifier Bandwidth
BW =
gm
2
π
C1
The following converter characteristics must be chosen:
VO
IO
— Desired output current
— Converter output peak–to–peak ripple voltage
VO
Vac
Vac(LL)
— Desired output voltage
— AC RMS line voltage
— AC RMS low line voltage
相關PDF資料 |
PDF描述 |
|---|---|
| MC34262P | POWER FACTOR CONTROLLERS |
| MC34262 | Power Factor Controllers(功率因數控制器) |
| MC34280 | Power Supply & Management IC for Handheld Electronic Products(用于手提電子產品的電源管理芯片) |
| MC3479 | Stepper Motor Driver(步進電機驅動器) |
| MC44BC375 | PLL Tuned VHF Audio/ Video High Integration Modulator ICs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC34262DG | 功能描述:功率因數校正 IC Critical Mode PFC w/OVP RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| MC34262DG | 制造商:ON Semiconductor 功能描述:Driver IC |
| MC34262DR2 | 功能描述:功率因數校正 IC Critical Mode PFC RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| MC34262DR2G | 功能描述:功率因數校正 IC Critical Mode PFC w/OVP RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| MC34262P | 功能描述:功率因數校正 IC Critical Mode PFC RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。