參數資料
型號: MC33993
廠商: 飛思卡爾半導體(中國)有限公司
英文描述: Multiple Switch Detection Interface(多開關監測接口)
中文描述: 多交換檢測接口(多開關監測接口)
文件頁數: 22/28頁
文件大?。?/td> 820K
代理商: MC33993
33993/D
22
Go to: www.freescale.com
Figure 12. MOSFET or LED Driver Output
The sequence of commands (from Normal mode with inputs
tri-state) required to set up the device to drive a MOSFET are
as follows:
wetting current timer enable command
–Disable SPn
wetting current timer (refer to
Table 4
, page 14).
metallic command
–Set SPn to 16 mA or 2.0 mA gate
drive current (refer to
Table 3
, page 13).
settings command
–Set SPn as switch-to-battery (refer to
Table 1
, page 12).
tri-state command
–Disable tri-state for SPn (refer to
Table 5
, page 14).
After the
tri-state command
has been sent (tri-state disable),
the MOSFET gate will be pulled to ground. From this point
forward the MOSFET may be turned on and off by sending the
settings command
:
settings command
–SPn as switch-to-ground (MOSFET
ON).
settings command
–SPn as switch-to-battery (MOSFET
OFF).
Monitoring of the MOSFET drain in the OFF state provides
open load detection. This is done by using an SGn input
comparator. With the SGn input in tri-state, the load will pull up
the SGn input to battery. With open load the SGn pin is pulled
down to ground through an external resistor. The open load is
indicated by a logic [1] in the SO data bit.
The
analog command
may be used to monitor the drain
voltage in the MOSFET ON state. By sourcing 2.0 mA of current
to the 1.5 k
resistor, the analog voltage on the SGn pin will be
approximately:
As the voltage on the drain of the MOSFET increases, so
does the voltage on the SGn pin. With the SGn pin selected as
analog, the MCU may perform the A/D conversion.
Using this method for controlling unclamped inductive loads
is not recommended. Inductive flyback voltages greater than
V
PWR
may damage the IC.
The SP0–SP7 pins of this device may also be used to send
signals from one module to another. Operation is similar to the
gate control of a MOSFET.
For LED applications a resistor in series with the LED is
recommended but not required. The switch-to-ground inputs
are recommended for LED application. To drive the LED use
the following commands:
wetting current timer enable command
–Disable SGn
wetting current timer.
metallic command
–Set SGn to 16 mA.
From this point forward the LED may be turned on and off using
the
tri-state command
:
tri-state command
–Disable tri-state for SGn (LED ON).
tri-state command
–Enable tri-state for SGn (LED OFF).
These parameters are easily programmed via SPI commands
in Normal mode.
Multiple 33993 Devices in a Module System
Connecting power to the 33993 and the MCU for Sleep mode
operation may be done in several ways.
Table 16
shows
several system configurations for power between the MCU and
the 33993 and their specific requirements for functionality.
SP0
SG0
SG13
16
mA
2.0
mA
4.0 V Ref
+
-
Comparator
To SPI
V
PWR
SG0
1.5 k
L
VBAT
AMUX
100 k
V
PWR
+
-
Comparator
2.0 mA
To SPI
4.0 V
Ref
2.0
mA
16
mA
16
mA
V
PWR
V
PWR
SG0
16
mA
2.0
mA
V
PWR
V
PWR
+
-
Comparator
To SPI
4.0 V Ref
SG13
Table 16. Sleep Mode Power Supply
MCU
V
DD
33993
V
DD
Comments
5.0 V
5.0 V
All wake-up conditions apply. (Refer to
Sleep
Mode
, page 18.)
5.0 V
0 V
SPI wake-up is not possible.
0 V
5.0 V
Sleep mode not possible. Current from
CS
pull
up will flow through MCU to V
DD
that has been
switched off. Negative edge of
CS
will put 33993
in Normal mode.
0 V
0 V
SPI wake-up is not possible.
V
SGn
= I
SGn
x 1.5 k
+ V
DS
F
Freescale Semiconductor, Inc.
For More Information On This Product,
n
.
相關PDF資料
PDF描述
MC33997 Switching Power Supply with Linear Regulators(帶線性穩壓器的開關電源)
MC33998 Switching Power Supply with Linear Regulators(帶線性穩壓器的開關電源)
MC34017 Telephone Tone Ringer(電話振鈴)
MC34063A DC-DC CONVERTER CONTROL CIRCUITS
MC34063AB DC-DC CONVERTER CONTROL CIRCUITS
相關代理商/技術參數
參數描述
MC33993DWB 功能描述:接口 - 專用 MSDI RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MC33993DWBR2 功能描述:接口 - 專用 MSDI RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MC33996EK 功能描述:電源開關 IC - 配電 16LOW SIDE SW 1.2OHM RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻(最大值):85 mOhms 開啟時間(最大值):400 us 關閉時間(最大值):20 us 工作電源電壓:3.2 V to 6.5 V 電源電流(最大值): 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
MC33996EKR2 功能描述:電源開關 IC - 配電 16LOW SIDE SW 1.2OHM RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻(最大值):85 mOhms 開啟時間(最大值):400 us 關閉時間(最大值):20 us 工作電源電壓:3.2 V to 6.5 V 電源電流(最大值): 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
MC33997DW 功能描述:IC SWITCH 3.3/5V SUPPLY 24-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源,ICERA E400,E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA,WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR)