參數資料
型號： MC33991
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： Gauge Driver Integrated Circuit(標尺驅動器集成電路)
中文描述： 儀表驅動集成電路（標尺驅動器集成電路）
文件頁數： 26/36頁
文件大小： 660K
代理商： MC33991
33991
26
Go to: www.freescale.com
calibration procedure was not successful. A clock calibration is
allowed only if the gauges are disabled or the pointers are not
moving, indicated by status bits ST4 and ST5.
Figure 7. Gauge Enable and Clock Calibration Example
Some applications may require a guaranteed maximum
pointer velocity and acceleration. Guaranteeing these
maximums requires the nominal internal clock frequency fall
below 1 MHz. The frequency range of the calibrated clock is
always below 1 MHz if PECR bit D4 is logic [0] when initiating a
calibration command, followed by an 8 μs reference pulse. The
frequency is centered at 1 MHz if bit D4 is logic [1].
The 33991 can be deceived into calibrating faster or slower
thantheoptimalfrequencybysendingacalibrationpulselonger
or shorter than the intended 8 μs. As long as the count remains
between four and 15 there is no clock calibration flag. For
applications requiring a slower calibrated clock, i.e., a motor
designed with a gear ratio of 120:1 (8 microsteps/degrees), a
longer calibration pulse is required. The device allows a SPI
selectable slowing of the internal oscillator, using the PECR
command so the calibration divisor safely falls within the four to
15 range when calibrating with a longer time reference. For
example, for the 120:1 motor the pulse would be 12 μs instead
of 8 μs. The result of this slower calibration results in the longer
step times necessary to generate pointer movements
meetingthe acceleration and velocity requirements. The
resolution of the pointer positioning decreases from 0.083
°
/
microstep (180:1) to 0.125
°
/microstep (120:1). The pointer
sweep range increases from approximately 340
°
to over 500
°.
Note:
Be aware a fast calibration could result in violations of the
motor acceleration and velocity maximums, resulting in missed
steps.
Pointer Deceleration Waveshaping
Constant acceleration and deceleration of the pointer results
in choppy movements when compared to air core movements.
Air core behavior can be simulated with appropriate wave
shaping during deceleration only. This shaping is achieved by
adding repetitive steps at several of the last step values. An
example is illustrated in Figure 8.
Figure 8. Deceleration Waveshaping
SI
SI
SCLK
CSB
PECR Command
8us Calibration Pulse
D15
D0
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
De
HOLDCNT=
6
4
3
3
3
2
2
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
n=
VELOCITY
Acceeae
ceerae
STEPS
F
Freescale Semiconductor, Inc.
For More Information On This Product,
n
.
相關PDF資料
PDF描述
MC33993 Multiple Switch Detection Interface(多開關監測接口)
MC33997 Switching Power Supply with Linear Regulators(帶線性穩壓器的開關電源)
MC33998 Switching Power Supply with Linear Regulators(帶線性穩壓器的開關電源)
MC34017 Telephone Tone Ringer(電話振鈴)
MC34063A DC-DC CONVERTER CONTROL CIRCUITS
相關代理商/技術參數
參數描述
MC33991DW 制造商:Freescale Semiconductor 功能描述:Gauge Driver Integrated Circuit
MC33991DWR2 制造商:Rochester Electronics LLC 功能描述:GUAGE DRIVER IC - Bulk
MC33993DWB 功能描述:接口 - 專用 MSDI RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MC33993DWBR2 功能描述:接口 - 專用 MSDI RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
MC33996EK 功能描述:電源開關 IC - 配電 16LOW SIDE SW 1.2OHM RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*